Hongsub Jee

Dr. Hongsub Jee

SungKyunKwan University

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 July 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Hongsub JeeHongsub Jee
Hongsub Jee
MPMin-Joon Park
Min-Joon Park
KJKiseok Jeon
Kiseok Jeon
CJChaehwan Jeong
Chaehwan Jeong
Jaehyeong LeeJaehyeong Lee
Jaehyeong Lee
Interference lithography is a promising method for fabricating large-area, defect-free three-dimensional photonic crystal structures which can be used for facilitating the realization of photonic devices with a fast processing time. Although they can be used in waveguides, resonators, and detectors, their repeated regular array patterns can only be used for limited applications. In this study, we demonstrate a method for fabricating large-area photonic crystal structures with controlled defects by combining interference lithography and two-photon lithography using a light-curable resin. By combining regular array structures and controlled patterns, monotonous but large-area regular structures can be obtained. Furthermore, the patterned structures have considerable potential for use in various applications, such as solar cells, sensors, photodetectors, micro-/nano-electronics, and cell growth.

25 October 2021 in Nanomaterials
Verified
Journal Article
Open access
PDF file
MKMinha Kim
Minha Kim
Hongsub JeeHongsub Jee
Hongsub Jee
Jaehyeong LeeJaehyeong Lee
Jaehyeong Lee
In recent printed electronics technology, a photo-sintering technique using intense pulsed light (IPL) source has attracted attention, instead of conventional a thermal sintering process with long time and high temperature. The key principle of the photo-sintering process is the selective heating of a thin film with large light absorption coefficients, while a transparent substrate does not heat by the IPL source. Most research on photo-sintering has used a xenon flash lamp as a light source. However, the xenon flash lamp requires instantaneous high power and is unsuitable for large area applications. In this work, we developed a new photo-sintering system using a high-power ultraviolet light emitting diode (UV-LED) module. A LED light source has many merits such as low power consumption and potential large-scale application. The silver nanoparticles ink was inkjet-printed on a polyethylene terephthalate (PET) and photo-sintered by the UV-LED module with the wavelength of 365 and 385 nm. The electrical resistivity as low as 5.44 × 10−6 Ω·cm (just about three times compared to value of bulk silver) was achieved at optimized photo-sintering conditions (wavelength of 365 nm and light intensity of 300 mW/cm2).

21 December 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
VCVu Minh Han Cao
Vu Minh Han Cao
JBJaesung Bae
Jaesung Bae
JSJoongpyo Shim
Joongpyo Shim
BHByungyou Hong
Byungyou Hong
Hongsub JeeHongsub Jee
Hongsub Jee
Jaehyeong LeeJaehyeong Lee
Jaehyeong Lee
Alternative photo-sintering techniques for thermal annealing processes are used to improve the morphology, layer properties, and enhance solar cell performance. The fast, nontoxic, low cost, and environmentally friendly characteristics of Cu2ZnSnS4 have led to its consideration as an alternative potential absorber layer in copper indium gallium diselenide thin film solar cells. This work investigates the photo-sintering process for the absorber layer of Cu2ZnSnS4 solar cells. A Cu2ZnSnS4 layer was grown by hot-injection and screen-printing techniques, and the characteristics of the photo-sintered Cu2ZnSnS4 layer were evaluated by X-ray Diffraction, Raman spectroscopy, Energy dispersive X-ray analysis, Ultraviolet-visible spectroscopy, and field emission scanning electron microscopes. Overall, the optimal composition was Cu-poor and Zn-rich, without a secondary phase, estimated optical band-gap energy of approximately 1.6 eV, and enhanced morphology and kesterite crystallization. Using an intensity pulse light technique to the CZTS layer, fabrication of the solar cell device demonstrated successfully, and the efficiency of 1.01% was achieved at 2.96 J/cm2.

27 November 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
JBJaesung Bae
Jaesung Bae
Hongsub JeeHongsub Jee
Hongsub Jee
YPYongseob Park
Yongseob Park
Jaehyeong LeeJaehyeong Lee
Jaehyeong Lee
Shingled photovoltaic (PV) modules with increased output have attracted growing interest compared to conventional PV modules. However, the area per unit solar cell of shingled PV modules is smaller because these modules are manufactured by dividing and bonding solar cells, which means that shingled PV modules can easily have inferior shading characteristics. Therefore, analysis of the extent to which the shadow affects the output loss is essential, and the circuit needs to be designed accordingly. In this study, the loss resulting from the shading of the shingled string used to manufacture the shingled module was analyzed using simulation. A divided cell was modeled using a double-diode model, and a shingled string was formed by connecting the cell in series. The shading pattern was simulated according to the shading ratio of the vertical and horizontal patterns, and in the case of the shingled string, greater losses occurred in the vertical direction than the horizontal direction. In addition, it was modularized and compared with a conventional PV module and a shingled PV module. The results confirmed that the shingled PV module delivered higher shading output than the conventional PV module in less shade, and the result of the shading characteristic simulation of the shingled PV module was confirmed to be accurate within an error of 1%.

16 December 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Hongsub JeeHongsub Jee
Hongsub Jee
YNYohan Noh
Yohan Noh
MKMinwoo Kim
Minwoo Kim
Jaehyeong LeeJaehyeong Lee
Jaehyeong Lee
Floating solar power has a higher power generation efficiency than existing solar power generation methods. It is easier to secure in an installation area as well as to connect to other renewable energy sources. Floating solar power is considered an essential component for achieving carbon neutrality because it compensates for the shortcomings of existing solar power systems and maximizes their advantages. In this study, a performance comparison was conducted between pivotless tracking-type and fixed-type solar power systems. These systems were installed at the Irwol Reservoir in Suwon, South Korea, and monitored for comparison between May 2019 and June 2020. The tracking-type system generated approximately 14% more energy than the fixed-type system; the performance was maximized in May, which showed 25.63% more output power, and the performance was minimized in winter, with 3% more generated power. Owing to its pivotless structure, this system can be used in the solar industry.

17 October 2020 in Nanomaterials
Verified
Journal Article
Open access
PDF file
Hongsub JeeHongsub Jee
Hongsub Jee
Guanying ChenGuanying Chen
Guanying Chen
PPParas N. Prasad
Paras N. Prasad
Tymish Y. OhulchanskyyTymish Y. Ohulchanskyy
Tymish Y. Ohulchanskyy
Jaehyeong LeeJaehyeong Lee
Jaehyeong Lee
In this paper, we report an approach to polymerization of a nanocomposite containing UV-polymerizable organic material and inorganic, NaYbF4:Tm3+ core-based nanoparticles (NPs), which are optimized for upconversion of near infrared (NIR) to ultraviolet (UV) and blue light. Our approach is compatible with numerous existing UV-polymerizable compositions and the NaYF4: Yb, Tm3+ core-based NPs are much more stable against harsh conditions than NIR organic photo-initiators proposed earlier. The use of a core-shell design for the NPs can provide a suitable method for binding with organic constituents of the nanocomposite, while maintaining efficient NIR-to-UV/blue conversion in the NaYbF4 core. The prepared photopolymerized transparent polymer nanocomposites display upconversion photoluminescence in UV, visible and NIR ranges. We also demonstrate a successful fabrication of polymerized nanocomposite structure with millimeter/submillimeter size uniformly patterned by 980 nm irradiation of inexpensive laser diode through a photomask.