Interference lithography is a promising method for fabricating large-area, defect-free three-dimensional photonic crystal structures which can be used for facilitating the realization of photonic devices with a fast processing time. Although they can be used in waveguides, resonators, and detectors, their repeated regular array patterns can only be used for limited applications. In this study, we demonstrate a method for fabricating large-area photonic crystal structures with controlled defects by combining interference lithography and two-photon lithography using a light-curable resin. By combining regular array structures and controlled patterns, monotonous but large-area regular structures can be obtained. Furthermore, the patterned structures have considerable potential for use in various applications, such as solar cells, sensors, photodetectors, micro-/nano-electronics, and cell growth.
High-power and lightweight photovoltaic (PV) modules are suitable for building-integrated photovoltaic (BIPV) systems. Due to the characteristics of the installation sites, the BIPV solar modules are limited by weight and installation area. In this study, we fabricated glass-free and shingled-type PV modules with an area of 1040 mm × 965 mm, which provide more conversion power compared to conventional PV modules at the same installed area. Further, we employed an ethylene tetrafluoroethylene sheet instead of a front cover glass and added an Al honeycomb sandwich structure to enhance the mechanical stability of lightweight PV modules. To optimize the conversion power of the PV module, we adjusted the amount of dispensed electrically conductive adhesives between the solar cells. Finally, we achieved a conversion power of 195.84 W at an area of 1.004 m2, and we performed standard reliability tests using a PV module that weighed only 9 kg/m2.
Nanoporous structures have attracted great attention in electronics, sensor and storage devices, and photonics because of their large surface area, large volume to surface ratio, and potential for high-sensitivity sensor applications. Normally, electron or ion beam patterning can be used for nanopores fabrication by direct writing. However, direct writing is a rather expensive and time-consuming method due to its serial nature. Therefore, it may not translate to a preferred manufacturing process. In this research, a perfectly ordered large-area periodic pattern in an area of approximately 1 cm2 has been successfully fabricated on various substrates including glass, silicon, and polydimethylsiloxane, using a two-step process comprising visible light-based multibeam interference lithography and subsequent pattern transfer processes of reactive ion etching and nanomolding. Additionally, the multibeam interference lithography templated anodized aluminum oxide process has been described. Since the fabrication area in multibeam interference lithography can be extended by using a larger beam size, it is highly cost effective and manufacturable. Furthermore, although not described here, an electrodeposition process can be utilized as a pattern transfer process. This large-area perfectly ordered nanopore array will be very useful for high-density electronic memory and photonic bandgap and metamaterial applications.
9 September 2024 in Solar Energy Materials and Solar Cells
Three-dimensional structured silicon solar cells have demonstrated remarkable potential for enhanced light absorption, yet their practical implementation remains limited by mechanical fragility. While microwire architectures offer superior optical properties through effective light scattering and radial junction formation, their high aspect ratio creates significant mechanical stress at the wire-substrate interface, leading to structural failure under physical strain. Here, we present conically etched microhole arrays (CEMA) that fundamentally address this challenge by inverting the conventional microwire concept while maintaining its optical and electrical advantages. Through rigorous coupled-wave analysis simulations, we optimize the geometric parameters of these inverted structures, demonstrating that controlled hole tapering significantly reduces surface reflection while preserving carrier collection efficiency. We develop a specialized fabrication process combining deep reactive ion etching with diffusion-limited wet chemical etching, enabling precise control over both hole geometry and surface morphology. The resulting honeycomb-like architecture exhibits exceptional mechanical stability under stress testing, while maintaining weighted average reflectance below 5% across the solar spectrum. This structural advantage, combined with efficient carrier collection through radial junctions, enables devices achieving 40 48 mA/cm2 short-circuit current density and 599 mV open-circuit voltage. The optimized CEMA solar cells demonstrate 18.4% power conversion efficiency─the highest reported for microhole-based silicon solar cells, providing a practical pathway toward mechanically robust high-efficiency photovoltaics.
Carrier-selective contacts (CSCs) for high-efficiency heterojunction solar cells have been widely studied due to their advantages of processing at relatively low temperatures and simple fabrication processes. Transition metal oxide (TMO) (e.g., molybdenum oxide, vanadium oxide, and tungsten oxide) thin films are widely used as hole-selective contacts (HSCs, required work function for Si solar cells > 5.0 eV). However, when TMO thin films are used, difficulties are faced in uniform deposition. In this study, we fabricated a copper (I) iodide (CuI) thin film (work function > 5.0 eV) that remained relatively stable during atmospheric exposure compared with TMO thin films and employed it as an HSC layer in an n-type Si solar cell. To facilitate efficient hole collection, we conducted iodine annealing at temperatures of 100–180 °C to enhance the film’s electrical characteristics (carrier density and carrier mobility). Subsequently, we fabricated CSC Si solar cells using the annealed CuIx layer, which achieved an efficiency of 6.42%.