Jianjun Gao

Prof. Jianjun Gao

Fu Zhou University
orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 May 2020 in Metals
Verified
Journal Article
Open access
PDF file
HGHaibin Geng
Haibin Geng
JLJinglong Li
Jinglong Li
JGJianjun Gao
Jianjun Gao
XLXin Lin
Xin Lin
Wire and arc additive manufacturing of stiffened ribs for fabricating large integral panel components holds promise for lightweight construction, but stress and warpage remain intractable problems. This work take stress in central lines as a research focus, theoretically analyzes stress evolution along central lines without a stress distribution hypothesis, then further develops prediction models of warpage, based on general beam theory. The stress and warpage models are then verified by experimental results. The results showed that below 40 layers, the stress in the top layer increased rapidly to the yield strength. Following the continuous deposition of up to 100 layers, stress increased slowly, then gradually trended to a constant level. After 100 layers of deposition, the top-layer-plane stress in the 10th layer decreased from 68 MPa to 5 MPa, and the plane stress in the 90th layer decreased from 296 MPa to 245 MPa. Post-heating treatment effect was important for temperature uniformity. The largest warpage (3.48 mm) happened when stiffener was designed as 30 layers.

25 August 2020 in Materials
Verified
Journal Article
Open access
PDF file
JGJianjun Gao
Jianjun Gao
JLJian Luo
Jian Luo
HGHaibin Geng
Haibin Geng
KCKai Cui
Kai Cui
ZZZhilong Zhao
Zhilong Zhao
LLLin Liu
Lin Liu
High aspect ratio tungsten nanowires have been prepared by selective dissolution of Nickel-aluminum-tungsten (NiAl−W) alloys which were directionally solidified at growth rates varying from 2 to 25 μm/s with a temperature gradient of 300 K·cm−1. Young’s modulus and electrical resistivity of tungsten nanowires were measured by metallic mask template method. The results show that the tungsten nanowires with uniform diameter and high aspect ratio are well aligned. The length of tungsten nanowires increases with prolongation of etching time, and their length reaches 300 μm at 14 h. Young’s modulus of tungsten nanowires is estimated by Hertz and Sneddon models. The Sneddon model is proper for estimating the Young’s modulus, and the value of calculating Young’s modulus are 260–460 GPa which approach the value of bulk tungsten. The resistivity of tungsten nanowires is measured and fitted with Fuchs−Sondheimer (FS) + Mayadas−Shatzkes (MS) model. The fitting results show that the specific resistivity of W nanowires is a litter bigger than the bulk W, and its value decreases with decreasing diameter.

20 January 2018 in Journal of the Electrochemical Society
Verified
Journal Article
Closed access
PDF file
LWLufeng Wei
Lufeng Wei
ZZZhilong Zhao
Zhilong Zhao
JGJianjun Gao
Jianjun Gao
KCKai Cui
Kai Cui
SCSen Chen
Sen Chen
LLLin Liu
Lin Liu
Lamellar Ni3Si microchannels and Ni3Si micropore arrays were fabricated in directionally solidified Ni–Ni3Si hypereutectic alloys by selective dissolution. Regular lamellar and rod-like structures were obtained at growth rates of 1–6 μm/s for the hypereutectic alloys. The dissolution of the lamellar or rod-like Ni phases while passivating the continuous Ni3Si matrix resulted in continuous microchannels or nanopore arrays in the Ni–Ni3Si hypereutectic alloys. During selective dissolution, SiO2 preferentially formed on the Ni3Si phase and retarded its dissolution. The width of the microchannel was 2.85 μm, and the micropore diameter was approximately 7.86 μm. The structural materials with narrow microchannels can be applied in the field of catalyst, microfiltration, and micro/nanostructure fabrication.

29 May 2018 in Journal of Materials Science
Verified
Journal Article
Closed access
PDF file
JGJianjun Gao
Jianjun Gao
ZZZhilong Zhao
Zhilong Zhao
LWLufeng Wei
Lufeng Wei
KCKai Cui
Kai Cui
JGJingying Guo
Jingying Guo
LLLin Liu
Lin Liu

27 June 2020 in Metals
Verified
Journal Article
Open access
PDF file
HGHaibin Geng
Haibin Geng
JLJian Luo
Jian Luo
JLJinglong Li
Jinglong Li
JGJianjun Gao
Jianjun Gao
XLXin Lin
Xin Lin
Molten pool uniformity is a prerequisite for wire and arc additive manufacture to achieve a uniform surface appearance. The thermal boundary is a key indicator to evaluate the thermodynamic state of the molten pool. This paper focuses on thermal analysis through finite element simulation and characterizes the thermal evolution of a molten pool during bottom-up deposition. The peak temperature of the substrate plate increases from 375.7 °C to 623.1 °C when peak current increases from 120 A to 180 A. The temperature gradient decreases from 40 °C/mm to 30 °C/mm. Weld speed increases from 0.15 m/min to 0.25 m/min; the temperature gradient is kept at about 30 °C/mm. Dimensionless thermal conductivity, Ge number, is proposed and defined as the criteria to estimate layer size variation. For Ip = 140 A, the average value of the Ge number is 87.7, and it shows the best numerical stability. Dimensionless thermal conductivity, Ge, is proposed and defined as the criteria to estimate the occurrence of layer size variation. Prolonging heating time and increasing cycle frequency, Ge number shows favorable stability during bottom-up deposition. The experimental results are consistent with analytical conclusions, which proves the validity of the Ge number as an indicator of deposition stability.

20 June 2017 in Journal of the Electrochemical Society
Verified
Journal Article
Closed access
PDF file
JGJianjun Gao
Jianjun Gao
ZZZhilong Zhao
Zhilong Zhao
LWLufeng Wei
Lufeng Wei
KCKai Cui
Kai Cui
Directionally solidified NiAl–W pseudobinary eutectic alloys were selectively etched using an electrochemical system of three electrodes with pulsed potentials to remove the W fibrous phase, and nanoporous NiAl matrix was obtained. Experimental results demonstrated that the ammonium acetate solution has better dissolving efficiency than Na2HPO4−C6H8O7 buffer solution in selectively dissolving the W phases. The dissolving rate at the pulsed potential of 0.5 V is much higher than that of 1.0 V in the same dissolving duration. For polarization at the pulsed potential of 0.5 V, the pore diameter is a constant of 0.22 μm and the dissolving depth increases during the dissolving duration. Over-dissolving occurred at the pulsed potential of 1.0 V, led to the enlargement of the pores on the NiAl matrix. The number of connecting pores in the sample evidently increased with solidification speed from 8 μm/s to 15 μm/s.