Zhilong Zhao

Dr. Zhilong Zhao


Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 July 2011 in Materials and Manufacturing Processes
Verified
Journal Article
Closed access
ZZZhilong Zhao
Zhilong Zhao
YLYan Liu
Yan Liu
LLLin Liu
Lin Liu
An experimental study on the influence of a pulsed magnetic field (PMF) on the unidirectional solidification of pure aluminum is reported. The forced convection induced by PMF encourages a thermal homogenization of the liquid zone ahead of the solidification front. Meanwhile, synchronous solidification occurs under high magnetic intensity to form fine equiaxed grains in the entire ingot. The solidification time exhibits a trend of going from initial ascent to subsequent decent with increasing magnetic intensity. Finally, the solidification times of various temperature measurement points in the casting approach a convergence point at a magnetic intensity of 0.154 T, at which the finest grain size appears in the ingots. A thermodynamic expression with the application of PMF is discussed.

31 January 2011 in Materials and Manufacturing Processes
Verified
Journal Article
Closed access
ZZZhilong Zhao
Zhilong Zhao
JWJianlong Wang
Jianlong Wang
LLLin Liu
Lin Liu
High voltage durative discharge was applied to unidirectional solidifying pure aluminum by discharging capacitor bank. The conditions to modify solidification structures, including initial voltage and capacitance of capacitor bank, were examined. The experimental results showed that the solidification structure was modified from columnar grains to equiaxed grains by increasing initial voltage and capacitance. However, coarsening of grain structures was observed when the discharge energy poured from the capacitor bank was excessive. The effect of pulse electric discharge on undercooling during solidification was analyzed, and the grain structures were simulated using cellular automaton methods based on nucleation theory.

1 February 2018 in Journal of Crystal Growth
Verified
Journal Article
Closed access
LWLufeng Wei
Lufeng Wei
ZZZhilong Zhao
Zhilong Zhao
JGJianjun Gao
Jianjun Gao
KCKai Cui
Kai Cui
JGJingying Guo
Jingying Guo
LLLin Liu
Lin Liu

21 February 2024 in Chinese Journal of Physics
Verified
Journal Article
Closed access
KCKai Cui
Kai Cui
GSGenghuan Song
Genghuan Song
WWWeichuan Wang
Weichuan Wang
HLHuanying Liu
Huanying Liu
YYYichuan Yang
Yichuan Yang
DCDong Chen
Dong Chen

25 August 2020 in Materials
Verified
Journal Article
Open access
PDF file
JGJianjun Gao
Jianjun Gao
JLJian Luo
Jian Luo
HGHaibin Geng
Haibin Geng
KCKai Cui
Kai Cui
ZZZhilong Zhao
Zhilong Zhao
LLLin Liu
Lin Liu
High aspect ratio tungsten nanowires have been prepared by selective dissolution of Nickel-aluminum-tungsten (NiAl−W) alloys which were directionally solidified at growth rates varying from 2 to 25 μm/s with a temperature gradient of 300 K·cm−1. Young’s modulus and electrical resistivity of tungsten nanowires were measured by metallic mask template method. The results show that the tungsten nanowires with uniform diameter and high aspect ratio are well aligned. The length of tungsten nanowires increases with prolongation of etching time, and their length reaches 300 μm at 14 h. Young’s modulus of tungsten nanowires is estimated by Hertz and Sneddon models. The Sneddon model is proper for estimating the Young’s modulus, and the value of calculating Young’s modulus are 260–460 GPa which approach the value of bulk tungsten. The resistivity of tungsten nanowires is measured and fitted with Fuchs−Sondheimer (FS) + Mayadas−Shatzkes (MS) model. The fitting results show that the specific resistivity of W nanowires is a litter bigger than the bulk W, and its value decreases with decreasing diameter.

20 January 2018 in Journal of the Electrochemical Society
Verified
Journal Article
Closed access
PDF file
LWLufeng Wei
Lufeng Wei
ZZZhilong Zhao
Zhilong Zhao
JGJianjun Gao
Jianjun Gao
KCKai Cui
Kai Cui
SCSen Chen
Sen Chen
LLLin Liu
Lin Liu
Lamellar Ni3Si microchannels and Ni3Si micropore arrays were fabricated in directionally solidified Ni–Ni3Si hypereutectic alloys by selective dissolution. Regular lamellar and rod-like structures were obtained at growth rates of 1–6 μm/s for the hypereutectic alloys. The dissolution of the lamellar or rod-like Ni phases while passivating the continuous Ni3Si matrix resulted in continuous microchannels or nanopore arrays in the Ni–Ni3Si hypereutectic alloys. During selective dissolution, SiO2 preferentially formed on the Ni3Si phase and retarded its dissolution. The width of the microchannel was 2.85 μm, and the micropore diameter was approximately 7.86 μm. The structural materials with narrow microchannels can be applied in the field of catalyst, microfiltration, and micro/nanostructure fabrication.