Seyed Vahid Hosseini

Dr. Seyed Vahid Hosseini

Assisant Professor
orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2021 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
FSFarhad Salek
Farhad Salek
MBMeisam Babaie
Meisam Babaie
SHSeyed Vahid Hosseini
Seyed Vahid Hosseini
OBO. Anwar Bég
O. Anwar Bég

1 December 2012 in Computational Materials Science
Verified
Journal Article
Closed access
SHSeyed Vahid Hosseini
Seyed Vahid Hosseini
MVMehrdad Vahdati
Mehrdad Vahdati

1 September 2020 in International Journal of Hydrogen Energy
Verified
Journal Article
Closed access
FSFarhad Salek
Farhad Salek
MZMohammad Zamen
Mohammad Zamen
SHSeyed Vahid Hosseini
Seyed Vahid Hosseini
Meisam BabaieMeisam Babaie
Meisam Babaie

1 November 2020 in Energy Reports
Verified
Journal Article
Open access
FSFarhad Salek
Farhad Salek
MZMohammad Zamen
Mohammad Zamen
SHSeyed Vahid Hosseini
Seyed Vahid Hosseini

3 September 2020 in Journal of Thermal Analysis and Calorimetry
Verified
Journal Article
Open access
PDF file
FSFarhad Salek
Farhad Salek
Meisam BabaieMeisam Babaie
Meisam Babaie
AGAli Ghodsi
Ali Ghodsi
SHSeyed Vahid Hosseini
Seyed Vahid Hosseini
AZAli Zare
Ali Zare
Number of hybrid vehicles has increased around the world significantly. Automotive industry is utilizing the hybridization of the powertrain system to achieve better fuel economic and emissions reduction. One of the options recently considered in research for hybridization and downsizing of vehicles is to employ waste heat recovery systems. In this paper, the addition of a turbo-compound system with an air Brayton cycle (ABC) to a naturally aspirated engine was studied in AVL BOOST software. In addition, a supercharger was modeled to charge extra air into the engine and ABC. The engine was first validated against the experimental data prior to turbo-compounding. The energy and exergy analysis was performed to understand the effects of the proposed design at engine rated speed. Results showed that between 16 and 18% increase in engine mechanical power can be achieved by adding turbo-compressor. Furthermore, the recommended ABC system can recover up to 1.1 kW extra electrical power from the engine exhaust energy. The energy and exergy efficiencies were both improved slightly by turbo-compounding and BSFC reduced by nearly 1% with the proposed system. Furthermore, installing the proposed system resulted in increase in backpressure up to approximately 23.8 kPa.

5 February 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Farhad SalekFarhad Salek
Farhad Salek
Meisam BabaieMeisam Babaie
Meisam Babaie
ASAmin Shakeri
Amin Shakeri
SHSeyed Vahid Hosseini
Seyed Vahid Hosseini
Timothy BodiscoTimothy Bodisco
Timothy Bodisco
AZAli Zare
Ali Zare
This study aims to investigate the effect of the port injection of ammonia on performance, knock and NOx emission across a range of engine speeds in a gasoline/ethanol dual-fuel engine. An experimentally validated numerical model of a naturally aspirated spark-ignition (SI) engine was developed in AVL BOOST for the purpose of this investigation. The vibe two zone combustion model, which is widely used for the mathematical modeling of spark-ignition engines is employed for the numerical analysis of the combustion process. A significant reduction of ~50% in NOx emissions was observed across the engine speed range. However, the port injection of ammonia imposed some negative impacts on engine equivalent BSFC, CO and HC emissions, increasing these parameters by 3%, 30% and 21%, respectively, at the 10% ammonia injection ratio. Additionally, the minimum octane number of primary fuel required to prevent knock was reduced by up to 3.6% by adding ammonia between 5 and 10%. All in all, the injection of ammonia inside a bio-fueled engine could make it robust and produce less NOx, while having some undesirable effects on BSFC, CO and HC emissions.