Wei Peng

Wei Peng


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 May 2020 in Materials
Verified
Journal Article
Open access
PDF file
YLYun Luo
Yun Luo
WGWenbin Gu
Wenbin Gu
WPWei Peng
Wei Peng
QJQiang Jin
Qiang Jin
QQQingliang Qin
Qingliang Qin
CYChunmei Yi
Chunmei Yi
In this paper, the effect of repair welding heat input on microstructure, residual stresses, and stress corrosion cracking (SCC) sensitivity were investigated by simulation and experiment. The results show that heat input influences the microstructure, residual stresses, and SCC behavior. With the increase of heat input, both the δ-ferrite in weld and the average grain width decrease slightly, while the austenite grain size in the heat affected zone (HAZ) is slightly increased. The predicted repair welding residual stresses by simulation have good agreement with that by X-ray diffraction (XRD). The transverse residual stresses in the weld and HAZ are gradually decreased as the increases of heat input. The higher heat input can enhance the tensile strength and elongation of repaired joint. When the heat input was increased by 33%, the SCC sensitivity index was decreased by more than 60%. The macroscopic cracks are easily generated in HAZ for the smaller heat input, leading to the smaller tensile strength and elongation. The larger heat input is recommended in the repair welding in 304 stainless steel.

26 May 2020 in Materials
Verified
Journal Article
Open access
PDF file
XHXiaodong Hu
Xiaodong Hu
HJHao-Yong Jiang
Hao-Yong Jiang
YLYun Luo
Yun Luo
QJQiang Jin
Qiang Jin
WPWei Peng
Wei Peng
CYChun-Mei Yi
Chun-Mei Yi
The repair reinforcement height is an important parameter of repair welding, which may have a great influence on structural integrity. In this paper, the effects of repair welding reinforcement height on the microstructure, microhardness, residual stresses and stress corrosion cracking (SCC) behavior of a 304 stainless steel-repaired joint were investigated by experimentation and simulation. With an increase of the repair weld reinforcement height, the δ ferrite content in weld and fusion zone is obviously reduced, and the ferrite shape is gradually changed from the skeleton to the worm shape. With the increase of repair welding reinforcement height, the microhardness and residual stresses decrease gradually. The tensile strength and elongation for higher repair weld reinforcement height are larger than those with lower repair weld reinforcement height. The higher the repair weld reinforcement height, the harder it is for SCC to occur. The repair welding in 304 stainless steel is recommended to be repaired no more than two times.

12 December 2023 in Metals
Verified
Journal Article
Open access
PDF file
Bin YangBin Yang
Bin Yang
GSGuang hua Sun
Guang hua Sun
XHXiaodong Hu
Xiaodong Hu
ZLZichen Liu
Zichen Liu
XXXuefang Xie
Xuefang Xie
XSXiaoming Shao
Xiaoming Shao
The non-uniformity of microstructures and mechanical properties across a whole welded joint is a crucial factor leading to its weakening performance and premature failure. Post-weld heat treatment is a primary method for increasing the mechanical properties. However, the evolution mechanism of mechanical properties related to heterogeneous microstructure after heat treatment remains unclear, making it challenging to design the heat treatment process and evaluate its effect comprehensively. In this study, microstructure characterization and a series of mechanical tests of 12Cr1MoV welded joint after the stress relief annealing (SRA) and tempering heat treatment (THT) were conducted. The effect of heat treatment on mechanical properties is analyzed based on the comparison between stress relief annealing and tempering heat treatment in terms of tensile properties, impact toughness, and impact fracture morphology. The results indicate that, after the tempering heat treatment, the evolution of mechanical properties in each subzone of the joint is consistent, i.e., the hardness and tensile strength decreased while the toughness increased. Notably, the most substantial enhancement in toughness is observed in the weld zone, primarily due to a significant reduction in the presence of pre-eutectoid ferrite. Furthermore, it is proved that hardness is an indicator to reflect changes in tensile strength related to the microstructure evolution, which indicates it can be employed to evaluate the effectiveness of post-weld heat treatment in practical engineering.