Modern computing technology is based on silicon. To date, a cost-effective and easy to implement method to obtain isotopically pure silicon is highly desirable for attaining efficient heat dissipation in microelectronic devices and for hosting spin qubits in quantum computing. We propose that it is possible to use a 28Si+ ion beam to obtain an isotopically pure near-surface region in wafer silicon. However, this requires a highly stable, high current, and isotopically pure 28Si ion beam. This work presents and discusses the instrumentation details and experimental parameters involved in generating this required ion beam. Silane is used as the precursor gas and is decomposed in a Penning ion source to generate a 28Si+ ion beam. The influence of key ion source parameters such as the gas flow rate, magnetic field strength, and anode voltage is presented. An isotopically pure 28Si+ ion beam with 10 ± 0.5 μA current on the target is obtained at the GNS Science 40 kV ion implanter. The beam was observed to be stable for at least 8 h and contains less than 700 ppm of other Si isotopes. This high current and high purity provides opportunities to explore efficient modification of the isotopic distribution in a native Si substrate at ambient temperature. The results highlight opportunities offered by using Penning ion source based low energy ion implanters for the synthesis of isotopically modified Si surface regions—a technique also applicable to other materials such as diamonds and diamond-like carbon.
Micrometre thick diamond‐like carbon (DLC) coatings produced by direct ion deposition were implanted with 30 keV Ar+ and transition metal ions in the lower percentage (<10 at.%) range. Theoretical calculations showed that the ions are implanted just beneath the surface, which was confirmed with RBS measurements. Atomic force microscope scans revealed that the surface roughness increases when implanted with Ar+ and Cu+ ions, whereas a smoothing of the surface from 5.2 to 2.7 nm and a grain size reduction from 175 to 93 nm are measured for Ag+ implanted coatings with a fluence of 1.24 × 1016 at. cm−2. Calculated hydrogen and carbon depth profiles showed surprisingly significant changes in concentrations in the near‐surface region of the DLC coatings, particularly when implanted with Ag+ ions. Hydrogen accumulates up to 32 at.% and the minimum of the carbon distribution is shifted towards the surface which may be the cause of the surface smoothing effect. The ion implantations caused an increase in electrical conductivity of the DLC coatings, which is important for the development of solid‐state gas sensors based on DLC coatings.
Magnetic sensors are key elements in many industrial, security, military, and biomedical applications. Heusler alloys are promising materials for magnetic sensor applications due to their high spin polarization and tunable magnetic properties. The dynamic field range of magnetic sensors is strongly related to the perpendicular magnetic anisotropy (PMA). By tuning the PMA, it is possible to modify the sensing direction, sensitivity and even the accuracy of the magnetic sensors. Here, we report the tuning of PMA in a Co2MnGa Heusler alloy film via argon (Ar) ion irradiation. MgO/Co2MnGa/Pd films with an initial PMA were irradiated with 30 keV 40Ar+ ions with fluences (ions·cm−2) between 1 × 1013 and 1 × 1015 Ar·cm−2, which corresponds to displacement per atom values between 0.17 and 17, estimated from Monte-Carlo-based simulations. The magneto optical and magnetization results showed that the effective anisotropy energy (Keff) decreased from ~153 kJ·m−3 for the un-irradiated film to ~14 kJ·m−3 for the 1 × 1014 Ar·cm−2 irradiated film. The reduced Keff and PMA are attributed to ion-irradiation-induced interface intermixing that decreased the interfacial anisotropy. These results demonstrate that ion irradiation is a promising technique for shaping the PMA of Co2MnGa Heusler alloy for magnetic sensor applications.
17 March 2021 in Journal of the Royal Society of New Zealand
This manuscript outlines current research activities based on ion beam science at GNS Science in New Zealand. Ion beam analysis methods include Rutherford backscattering and nuclear reaction analysis which trace back to Rutherford's famous ‘gold foil’ and ‘splitting the atom’ experiments. These ion beam‐based methods generally offer the ability to analyse materials for every element of the periodic table, to ppm concentrations, and with depth profiles ranging from a few nm to several microns. Ion beam methods are now also used to modify and create new materials precisely. Rutherford's early research now has a legacy at GNS Science's Materials team to discover, design, and develop materials for energy efficient modern applications for a low carbon future. These include magnetic sensors for security products, nanostructured magnetic materials for energy conversion, thermoelectric devices for energy harvesting, and catalytic development for clean energy carriers and energy efficient communication devices.