These days, electric motor qualities and energy-saving problems are significant to our society. The critical component of these problems is related to magnetic materials. In this respect, here, we investigated the (FexCo1−x)72B19.2Si4.8Nb4 (0 ≤ x ≤ 1, at 0.1 intervals) ribbon alloys’ structural, thermal, and magnetic properties. Replacing Co with Fe turned out to increase saturation magnetization up to 127.7 emu/g and improve thermal stability. Additionally, we conducted heat treatment at 843, 893, and 943 K for 10 mins, and the annealing effect in the amorphous (FexCo1−x)72B19.2Si4.8Nb4 (0.4 ≤ x ≤ 0.9, at 0.1 intervals) ribbons on structural and magnetic properties are analyzed. The saturated magnetization (Ms) value has increased by about 20 to 30 emu/g by the heat treatment and tends to increase as the annealing temperature increases until the annealing temperature approaches 893 K. After annealing at 943 K for 10 mins, the highest saturation magnetization of 156.8 emu/g was achieved. In addition, all four samples show the same coercivity trend. The coercivity decreases when the initial heat treatment at 843 K is applied to the ribbons. However, after annealing at this high temperature, such as 893, 943 K, the Fe3B, and (Fe, Co)23B6 phases are also generated and cancel out the good soft magnetic properties of α-(Fe, Co) phase.
In the Fe-Co alloy system, the addition of Cr improves the glass-forming ability (GFA) with superior soft magnetic properties such as high saturation magnetization (Ms) and low coercivity (Hc). In addition, Cr is considered to be an important factor for improving the corrosion resistance of Fe-based amorphous alloy. Therefore, in the present study, we investigated the GFA, soft magnetic properties, and corrosion resistance of the as-spun ribbons in [Co0.075Fe0.675B0.2Si0.05]100−xCrx (x = 0–8) alloy system. The ribbons were produced using the melt-spinning technique and were characterized by X-ray diffraction, differential scanning calorimetry, thermomechanical analysis, and vibrating sample magnetometer. The Co-Fe-B-Si-Cr alloys exhibited high thermal stability and a high Ms of 0.93–1.53 T. Corrosion properties were evaluated by cyclic voltammetry. The addition of Cr improved the corrosion resistance of the alloys. The alloys with a higher Cr content exhibited a higher corrosion resistance. The optimum combination with soft magnetic properties and corrosion resistance of Fe-co based amorphous alloys can be utilized for extensive fields of application through a variation of Cr contents.
To increase the saturation magnetization (Ms) of commercially available soft magnetic Finemet alloys to the level comparable to that of Si-steel and Fe-based nanocrystalline alloys such as Nanoperm, Nanomet, the B or Si content in combination with annealing heat treatment was tailored. The ribbons of Fe95−xSi1BxNb3Cu1 (x = 11, 12, 13) and Fe87−xSixB9Nb3Cu1 (x = 6, 8, 10) were prepared by melt-spinning and annealed at different temperatures to develop nanocrystalline microstructure optimizing the soft magnetic properties. The magnetic properties of the as-spun and annealed ribbons were measured using a vibrating sample magnetometer and AC B-H loop tracer to acquire Ms of above 1.4 T in all as-spun ribbons. Among the alloys, Fe84Si1B11Nb3Cu1 annealed at 545 °C showed the highest Ms of 2 T, which exceeds that of the conventional Finemet and other Fe-based nanocrystalline alloys.
The soft magnetic amorphous ribbons of (FexCo1−x)85M9Nb1B5 (M = Zr or Hf, x = 0.4, 0.5, 0.6, 0.7, 0.8, and 0.9) were investigated in this study. Replacing Zr by Hf turned out to increase saturation magnetization and, at the same time, reduce the coercivity, both of which serve together in enhancing the soft magnetic performance of the alloys. Moreover, the optimum ratio of Fe/Co was determined after the survey on different alloys with varying Fe/Co ratio resulting in the maximum saturation magnetization while keeping the coercivity low. After optimization, the highest saturation magnetization of 1.62 T was achieved with coercivity of 11 A/m. While substitution of Hf for Zr slightly reduced the crystallization onset temperature of the amorphous structure, the thermal stability of the soft magnetic amorphous alloys was not significantly affected by the Zr/Hf replacement.