A major challenge in processing 7xxx series aluminum alloys is their limited formability at room temperature. In this paper, for the alloys EN AW-7020 and EN AW-7075, various variants of the W-temper forming process are investigated. For both alloys, a good cold formability and a high strength after aging can be achieved. The effects of solution heat treatment or retrogression temperature and holding time, as well as the influence of plastic deformation after quenching, were studied. For various combinations of process parameters, the formability of the as-quenched materials and the hardening performance during artificial aging were examined. For this, hardness measurements and differential scanning calorimetry (DSC) experiments were performed along the entire process chain, to reveal the development of the hardening precipitates. After solution heat treatment and quenching, the yield stress and hardness of both investigated alloys were drastically reduced in comparison to their initial T6 states, while the ductility was significantly increased. By a subsequent simple artificial aging treatment, the same hardness as in the T6 state could be restored. It was observed that plastic deformation immediately after quenching significantly decreased the artificial aging time to achieve the peak hardness. Besides the conventional solution heat treatment process, an alternative retrogression and re-aging procedure was identified for the alloy EN AW-7020. While the heat treatment temperature can be reduced as compared to the conventional solution heat treatment, the formability and hardenability are equally good. In contrast, no such alternative process could be identified for the alloy EN AW-7075.
1 November 2018 in International Journal of Solids and Structures
Grain growth is a significant phenomenon for the thermomechanical processing of metals. Since the mobility of the grain boundaries is thermally activated and energy stored in the grain boundaries is released during their motion, a mutual interaction with the process conditions occurs. To model such phenomena, a thermodynamic framework for the representation of thermomechanical coupling phenomena in metals including a microstructure description is required. For this purpose, Rational Extended Thermodynamics appears to be a useful tool. We apply an entropy principle to derive a thermodynamically consistent model for grain coarsening due to the growth and shrinkage of individual grains. Despite the rather different approaches applied, we obtain a grain growth model which is similar to existing ones and can be regarded as a thermodynamic extension of that by Hillert (1965) to more general systems. To demonstrate the applicability of the model, we compare our simulation results to grain growth experiments in pure copper by different authors, which we are able to reproduce very accurately. Finally, we study the implications of the energy release due to grain growth on the energy balance. The present unified approach combining a microstructure description and continuum mechanics is ready to be further used to develop more elaborate material models for complex thermo-chemo-mechanical coupling phenomena.
25 October 2016 in Proceedings in Applied Mathematics and Mechanics
The formation of adiabatic shear bands (ASBs) is a phenomenon of highly localized shear deformation in metallic materials that occurs especially at high shear strain rates. From a conventional thermo-mechanical perspective, local rapid heating induced by deformation at high strain rates leads to local thermal softening. In this study, we investigate the thermo-mechanical behavior of, and ASB formation in, the non-age-hardenable aluminum alloy AA5754. Compression tests with cylindrical specimens are performed at different temperatures (in the range from 293 K to 673 K) and a wide range of nominal strain rates between 10-4 and 103 s-1. Moreover, we use S-shaped samples and digital image correlation for the in-situ characterization of shear banding under quasi-static and dynamic conditions, and we perform microhardness measurements and electron backscatter diffraction analysis for a post-mortem analysis of microstructural changes associated with different stages of shear deformation. Our results show that the material behavior is dominated by dynamic strain aging effects and micro-shear band formation under quasi-static loading, whereas dynamic loading conditions are associated with a pronounced localization of deformation, leading to local shear strain rates exceeding 30,000 s-1, and substantial grain refinement that can be inferred from a substantial increase of subgrain boundary density inside the ASB. Clearly, formation and growth of shear bands depends strongly on the applied strain rate. Distinctly different microstructural deformation mechanisms occur and determine microstructural evolution as well as the resulting local material properties.