Alexander Butz

Alexander Butz

Auto-generated profile, based on publicly available information

Alexander Butz

Fraunhofer IWM, 79108 Freiburg, Germany

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 October 2020 in Metals
Verified
Journal Article
Open access
PDF file
shreyas hebbarshreyas hebbar
shreyas hebbar
LKLukas Kertsch
Lukas Kertsch
ABAlexander Butz
Alexander Butz
A major challenge in processing 7xxx series aluminum alloys is their limited formability at room temperature. In this paper, for the alloys EN AW-7020 and EN AW-7075, various variants of the W-temper forming process are investigated. For both alloys, a good cold formability and a high strength after aging can be achieved. The effects of solution heat treatment or retrogression temperature and holding time, as well as the influence of plastic deformation after quenching, were studied. For various combinations of process parameters, the formability of the as-quenched materials and the hardening performance during artificial aging were examined. For this, hardness measurements and differential scanning calorimetry (DSC) experiments were performed along the entire process chain, to reveal the development of the hardening precipitates. After solution heat treatment and quenching, the yield stress and hardness of both investigated alloys were drastically reduced in comparison to their initial T6 states, while the ductility was significantly increased. By a subsequent simple artificial aging treatment, the same hardness as in the T6 state could be restored. It was observed that plastic deformation immediately after quenching significantly decreased the artificial aging time to achieve the peak hardness. Besides the conventional solution heat treatment process, an alternative retrogression and re-aging procedure was identified for the alloy EN AW-7020. While the heat treatment temperature can be reduced as compared to the conventional solution heat treatment, the formability and hardenability are equally good. In contrast, no such alternative process could be identified for the alloy EN AW-7075.

1 April 2020 in Mechanics of Materials
Verified
Journal Article
Closed access
Ali Cheloee DarabiAli Cheloee Darabi
Ali Cheloee Darabi
VGVinzenz Guski
Vinzenz Guski
ABAlexander Butz
Alexander Butz
JKJavad Kadkhodapour
Javad Kadkhodapour
Siegfried SchmauderSiegfried Schmauder
Siegfried Schmauder

1 November 2019 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
ABA Butz
A Butz
AWA Wessel
A Wessel
JPJ Pagenkopf
J Pagenkopf
DHD Helm
D Helm
The parameter identification of anisotropic 3D yield functions for sheet metals based on experimental data is very difficult, because material properties associated to the out-of-plane stress states cannot be directly measured. An alternative and promising approach for identifying parameters of anisotropic yield models, and particularly for 3D yield models, is the concept of virtual testing. Within the presented work, a full-field microstructure simulation framework based on a crystal plasticity (CP) model is used to determine macroscopic mechanical properties of a ferritic deep drawing steel DX56 within 3D stress space. The results are utilized to identify the parameter of anisotropic 2D and 3D yield models according to Hill [1] and Barlat [2, 3].

1 April 2010 in International Journal of Material Forming
Verified
Journal Article
Closed access
PDF file
ABA. Butz
A. Butz
SLS. Lossau
S. Lossau
BSB. Springub
B. Springub
FRFranz Roters
Franz Roters

26 February 2025 in Advanced Engineering Materials
Verified
Journal Article
Open access
FRFranz Roters
Franz Roters
AAAhmed Aslam
Ahmed Aslam
YBYang Bai
Yang Bai
MBMatthias Büschelberger
Matthias Büschelberger
KBKirill Bulert
Kirill Bulert
DHDirk Helm
Dirk Helm
The innovative strength of the steel industry is based on the mastery of microstructure–property relationships. Digital workflows can largely contribute to this aim by making the complexity of workflows reproducible and their execution user independent. In this work, the tools and workflows developed in the project StahlDigital as part of the German MaterialDigital initiative are presented and application examples are provided. A steel ontology builds the foundation for data collection and storage as well as for the semantic description of experimental and simulation data processing workflows. A dataspace powered by the Dataspace Management System (DSMS) digitally represents such workflows and manages data along them in a Findable, Accessible, Interoperable, Reusable manner aiming to derive new knowledge. Experimental data processed via DSMS can be further evaluated and used as input for simulation workflows. The simulations included in such workflows are run by the workflow system pyiron, which has been semantically extended in StahlDigital for this purpose.

21 December 2024 in Materials Science and Engineering: A
Verified
Journal Article
Open access
AWAlexander Wessel
Alexander Wessel
SPsemih perdahcioglu
semih perdahcioglu
Ton Van den BoogaardTon Van den Boogaard
Ton Van den Boogaard
ABAlexander Butz
Alexander Butz
WVWolfram Volk
Wolfram Volk