Titanium dioxide is used extensively in ultraviolet-visible irradiation to induce oxidation. However, this method relies on daylight harvesting. Alternatively, our experiment utilized titanium dioxide directly under thermal excitation. Three different titanium oxide-based catalysts, i.e., commercial titanium dioxide Degussa P25, black titanium dioxide, and black titanium dioxide modified with copper oxide, were investigated at moderate temperatures (70 and 120 °C). The utilization of titanium-based catalysts with tert-butyl hydroperoxide (TBHP) in alkaline water is practical for oxidizing carbonyl derivatives of furan to one or two carbon-less carboxylic acids, such as succinic acid (selective to 38-87%), furoic acid (selective to 0-70%), and maleic acid (selective to 3-39%), under moderate conditions. These titanium-based catalysts differ in their physicochemical properties, resulting in variations in their catalytic activity and selectivity, and are active at different temperatures. Electron paramagnetic resonance (EPR) revealed no traces of oxygen vacancy sites on the titanium oxide. In contrast, black titanium dioxide consisted of an oxygen vacancy with one electron, whereas copper-modified black titanium dioxide consisted of a doubly ionized oxygen vacancy.
Nickel supported on a zeolite Linde Type A 5A (zeolite LTA 5A) catalyst (Ni/zeolite LTA 5A) was fabricated into cylindrical pellets using two types of binders: methylcellulose (MC) with poly(vinyl alcohol) (PVA) and glutinous flour (GF). Carbon dioxide methanation was conducted under atmospheric pressure at 200–500 °C. The gas hourly space velocity (GHSV) was varied from 1,125 to 15,000 h–1, corresponding to volumetric flow rates of 60–500 mL/min. The conversion of carbon dioxide to methane decreased as GHSVs increased. Fabricated catalysts produced higher methane yields than the catalyst powder, with CO2-to-CH4 conversion rates of 70–90% and 10–90%, respectively. The CO2 conversion of the catalyst with MC+PVA approached 90% at 400 °C, superior to that of the catalyst with GF, which reached 84% at the same temperature and a volumetric flow rate of 60 mL min–1. The most active temperature for CO2 methanation was 400 °C, and nearly all catalysts were selective to methane, with selective rates exceeding 80%. The stabilities of the fabricated catalysts were tested over 96 h. The stability of the catalyst with MC+PVA was noncomparable to that of the catalyst with GF, since the catalyst with MC+PVA exhibited a 1–6% reduction in activity after 36 h, owing to nickel metal sintering, whereas the catalyst with GF binder exhibited minor fluctuations and remained stable within 96 h. The employed catalysts lost their configurated shapes, existing only as small particles due to binder decomposition.
The development of low-cost and durable adsorbents for post-combustion CO₂ capture remains a critical challenge. In this study, zeolite LTA 5A was modified using aqueous ammonia (NH₄OH) and monoethanolamine (MEA) to examine how nitrogen-containing additives influence surface properties and CO₂ adsorption performance in both powder and granulated forms. Structural and physicochemical characterization (XRD, SEM–EDS, FTIR, BET, and CO₂-TPD) confirmed preservation of the zeolite framework after modification, while spectroscopic and desorption analyses indicated the introduction of nitrogen-containing functionalities. Considering the limitations of EDS for nitrogen quantification, correlations are drawn based on observable changes in surface chemistry and porosity. Functionalization reduced N₂-accessible surface area and pore volume but enhanced CO₂ affinity under dynamic conditions. In fixed-bed breakthrough experiments at ambient conditions with 5 vol.% CO₂, the NH₄OH-modified powder exhibited the highest dynamic capacity (8.8 mmol g⁻¹) and capture efficiency (68%), outperforming unmodified and MEA-treated samples. Additionally, the NH₄OH-functionalized adsorbent demonstrated stable cyclic performance over repeated adsorption–desorption cycles with minimal capacity loss. These results demonstrate that simple ammonia-based functionalization provides an effective and scalable strategy to enhance CO₂ capture performance and stability of zeolite 5A under practical operating conditions.