Purpose: The purpose of this paper is to offer an introduction to the technological advances of the complementary metal–oxide–semiconductor (CMOS) image sensors along the past decades. The authors review some of those technological advances and examine potential disruptive growth directions for CMOS image sensors and proposed ways to achieve them. Design/methodology/approach: Those advances include breakthroughs on image quality such as resolution, capture speed, light sensitivity and color detection and advances on the computational imaging. Findings: The current trend is to push the innovation efforts even further, as the market requires even higher resolution, higher speed, lower power consumption and, mainly, lower cost sensors. Although CMOS image sensors are currently used in several different applications from consumer to defense to medical diagnosis, product differentiation is becoming both a requirement and a difficult goal for any image sensor manufacturer. The unique properties of CMOS process allow the integration of several signal processing techniques and are driving the impressive advancement of the computational imaging. Originality/value: The authors offer a very comprehensive review of methods, techniques, designs and fabrication of CMOS image sensors that have impacted or will impact the images sensor applications and markets.
25 June 2018 in IEEE Transactions on Circuits and Systems I: Regular Papers
This work presents a hybrid column-parallel time-to-digital-converter interpolated (TDC) single-slope (SS) ADC with a digital delay element feedback. The proposed scheme solves the multiphase clock period matching problem in flash TDC-interpolation of SS ADCs without the use of a delay-locked-loop. The architecture employs open-loop delay elements for multiphase clock generation forming a lowered TDC radix of <2 adding redundancy and providing ability for gain calibration using a per-column digital multiplication operation. The presented digital feedback correction scheme is applied online and in-column after the end of each conversion, occupying less than 5% of the ramp time. The architecture is verified on a 1024 $x$ 128 linescan image sensor testchip manufactured in a 0.13-μm 1P3M CMOS process. The ADC operates at 250 MHz and achieves a 1-μs ramp time and 4.4-μs digital correlated double sampling row time for a 12-bit linear A/D conversion.
Logarithmic cameras have the wide dynamic range required to image natural scenes and encode the important contrast information within the scene. However, the images from these cameras are severely degraded by a fixed pattern noise (FPN). Previous attempts to improve the quality of the images from these cameras by removing an additive FPN have led to disappointing results. Using an existing model for the response of logarithmic pixels, it is concluded that the residual FPN in these images is caused by gain variations between pixels. In order to reduce the effects of these variations, a readout circuit, which is based upon a differential amplifier, has been used. However, even with this readout circuit, high-quality images will only be obtained if each image is corrected to remove the effects of both gain and offset variations. Measurement results are presented that show that the quality of the output from the logarithmic pixels is significantly improved if an electronic-calibration procedure is used to correct for both types of variations. In fact, with this procedure, the contrast sensitivity of the logarithmic pixels becomes comparable to that of the human eye over five decades of illumination intensity
29 September 2009 in IEEE Transactions on Electron Devices
An integrating CMOS image sensor with a wide dynamic range is described. The dynamic range of these pixels is controlled by a user-defined reference voltage that creates a photocurrent-dependent effective integration time. The operation of these pixels and a method of obtaining a well-controlled logarithmic response are both described. Furthermore, described are the results of two alternative methods of correcting the fixed pattern noise in these pixels and measurements of the temporal noise from individual pixels. These results show that with these pixels, it is possible to match the contrast sensitivity of the human visual system.
This paper reports a method of determining the system matrix of a nearest neighbor coupled array of micro/nanomechanical resonators. The simple method requires contacts to only one element of the array to determine two sets of eigenvalues related to the system matrix. The elements of the system matrix are then determined from these eigenvalues. This system matrix can then be used to determine the characteristics of the individual resonators or as the starting point for a perturbation analysis to determine the changes observed when a functionalized array of resonators is used as a sensor.
Previously, pixels have been proposed that combine the low-light sensitivity of linear pixels with the high dynamic range of pixels that have a logarithmic response. In this paper, a model for this type of pixel is presented that represents the response of the pixel over a wide range of photocurrents. Simulation and measurement results are presented to validate the model and to show that there is a simple procedure for determining the parameters of the model.