Visible light communications is an alternative method of indoor wireless communications that requires sensitive receivers. Ideally, single photon avalanche detectors (SPADs) could be used to create more sensitive receivers. However, the dead time, finite output pulse width, and photon detection efficiency of existing SPAD arrays limit their sensitivity and bandwidth. In this paper, an accurate equation for the impact of dead time on the sensitivity of a SPAD array is presented. In addition, the impact of the width of the output pulses on the on-off keying data rate is investigated. Finally, a comparison between receivers containing an avalanche photo-diode (APD) and a large array of SPADs shows that although the receiver containing the SPAD is more sensitive in the dark, the APD-based receiver is more sensitive in a normal operating condition. However, the models that predict the performance of both receivers suggest that newer SPAD arrays will enable significant improvements in receiver sensitivity.
The field of view and gain of optical concentrators used within free space optical communications systems are constrained by conservation of etendue. In this Letter, consideration of the processes in a fluorescent concentrator leads to a simple design strategy for these concentrators for this application. Significantly, because fluorescent concentrators do not conserve etendue, this can lead to concentrators with wider fields of view and higher gains. A model of a fluorescent concentrator containing a quantum dot material suggests that it could have a gain 50 times higher than an etendue conserving concentrator with the same field of view.
11 February 2020 in IEEE Photonics Technology Letters
The growing demand for wireless communications services means that RF systems are increasingly unable to support user’s requirement. Consequently, there is a growing interest in using visible light communication (VLC), including interest in sensitive VLC receivers. Since they have the potential to detect single photons, silicon photomultipliers (SiPMs) could potentially be used to create the most sensitive possible VLC receivers. In this paper, results of experiments to determine the optimum bias voltage and dynamic range of an off-the-shelf SiPM are reported. Results are then presented which show that in 500 lux of ambient light this receiver supports data rates of more than 2 Gbps with a bit-error-rate (BER) of 10–3.
A silicon photomultiplier (SiPM) could be used to create visible light communications receivers whose sensitivity is determined by shot-noise. However, its finite output pulse width will limit its bandwidth and its recovery time and dark count rate could limit its sensitivity. In this paper, a method of accurately determining the signal levels needed to transmit data in a shot-noise limited system using PAM is described. In addition, a method of estimating the additional power needed to use equalisation to overcome inter-symbol interference caused by the finite output pulse width of SiPMs is described. The best way to achieve more than 1 Gbps with this type of receiver and how to select the best available SiPM as a receiver are then discussed.
30 March 2021 in IEEE Photonics Technology Letters
A relationship between irradiance and the current needed to maintain the bias voltage applied to a silicon photomultiplier (SiPM) is shown to agree with experimental data. In addition to showing the saturation of the SiPMs response this relationship can be used to determine the power consumed by an SiPM. In addition, results are presented which show that, because of its higher maximum photon count rate, a 30020 SiPM can achieve a bit error rate (BER) of 10 -3 at a data rate of 3.45 Gbits/s.
15 November 2018 in IEEE Internet of Things Journal
Using optical communications for smart dust applications enables small size of transceivers and offers a potentially large power advantage over RF. This paper presents an optically powered transceiver, which consists of on-chip solar cells, an optical receiver, a storage capacitor and a passive transmitter formed by a liquid crystal modulator and a modulated retro-reflector (MRR). The transceiver circuit system has been fabricated using a standard 0.18μm CMOS process and the circuit area is 1*1.7mm² excluding the MRR. Measurement results show that the complete transceiver can successfully work for 1kbps downlink and 10bps uplink under 0.5V voltage supply and consume 53nA totally. This indicates the transceiver can work at least in a 10 meter range. It is successfully demonstrated that the transceiver scavenged the power from a 670nm modulated laser beam sent by a base station, extracted clock signal and the encoded data from the beam, decoded two designed instructions, switched the liquid crystal in the MRR and sent responses back to the base station. To the author’s best knowledge, this is the first time to present that an on-chip solar-cell powered transceiver realizes the two-way optical wireless communications for IoT applications.