Laurentiu Constantin Ceatra

Dr. Laurentiu Constantin Ceatra

Romanian Research and Development Institute for Gas Turbines COMOTI

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
Grigore CicanGrigore Cican
Grigore Cican
DMDeaconu Marius
Deaconu Marius
RMRadu Mirea
Radu Mirea
LCLaurentiu Constantin Ceatra
Laurentiu Constantin Ceatra
MCMihaiella Cretu
Mihaiella Cretu
The paper is presenting the experimental analysis of the use of biodiesel from waste sunflower oil and a blend of sunflower oil with palm oil as fuel for aviation turbo-engines. A comparative analysis for fuel mixtures made of Jet A + 5% Aeroshell 500 Oil (Ke) with 10%, 30%, and 50% for each bio-fuel type has been performed and Ke has been used as reference. Firstly, the following physical and chemical properties were determined: density, viscosity, flash point, freezing point, calorific power. Then, elemental analysis and Fourier transform infrared spectroscopy (FTIR) analysis were conducted for Ke, biodiesel obtained from recycled sunflower oil (SF), biodiesel obtained from blending recycled sunflower oil, and recycled palm oil (SFP), and for each fuel blend. Secondly, experimental tests of the blends have been conducted on the Jet Cat P80® micro-turbo engine (Gunt Hamburg, Barsbüttel, Germany). The tests have been conducted at different engine working regimes as follows: idle, cruise, intermediate, and maximum. For each regime, a one-minute testing period was chosen, and the engine parameters have been monitored. The turbo engine instrumentation recorded the temperature after the compressor and before the turbine, the fuel consumption and air flow, pressure inside the combustion chamber, and generated thrust. The burning efficiency and the specific consumption have been calculated for all four above-mentioned regimes and for all fuel blends. Two accelerometers have been installed on the engine’s support to register radial and axial vibrations allowing the assessment of engine stability.

21 September 2020 in Processes
Verified
Journal Article
Open access
PDF file
Grigore CicanGrigore Cican
Grigore Cican
DMDeaconu Marius
Deaconu Marius
RMRadu Mirea
Radu Mirea
LCLaurentiu Constantin Ceatra
Laurentiu Constantin Ceatra
MCMihaiella Cretu
Mihaiella Cretu
TDTănase Dobre
Tănase Dobre
This paper presents an analysis of the possibility of using recycled pork fat-based biodiesel as fuel for aviation turbo-engines. The analysis consists of the assessment of four blends of Jet A kerosene with 10%, 30%, 50%, and 100% biodiesel and pure Jet A that was used as reference in the study. The first part of the paper presents the physical-chemical properties of the blends: density, viscosity, flash point, freezing point, and calorific power. Through Fourier transform infrared spectroscopy (FTIR) analysis, a benchmark was performed on the mixtures of Jet A with 10%, 20%, 30%, 50%, and 100% biodiesel compared with Jet A. The second part of the paper presents the test results of these blends used for fuelling a Jet Cat P80 turbo engine at the Turbo Engines Laboratory of the Aerospace Engineering Faculty of Polyethnic University of Bucharest. These functional tests were performed using different operating regimes as follows: idle, cruise, intermediate, and maximum. For each regime, a testing period of around 1 min was selected and the engine parameters were monitored during the test execution. The burning efficiency was calculated for the maximum regime for all mixtures. To evaluate the functioning stability of the turbo engine using biodiesel, two accelerometers were mounted on the engine support that recorded the radial and axial vibrations. Moreover, to assess the burning stability and to identify other acoustic spectral components when biodiesel is used, two microphones were placed near the jet region. A comparative analysis between blends was made by taking the Jet A fuel as reference.

21 January 2023 in Sustainability
Verified
Journal Article
Open access
PDF file
Grigore CicanGrigore Cican
Grigore Cican
DCDaniel Eugeniu Crunteanu
Daniel Eugeniu Crunteanu
RMRadu Mirea
Radu Mirea
LCLaurentiu Constantin Ceatra
Laurentiu Constantin Ceatra
CLConstantin Leventiu
Constantin Leventiu
An experimental assessment of burning behavior of some aviation fuel and biodiesel obtained from waste oil mixture has been performed within this paper. The biodiesel was obtained from sunflower and palm waste oil (SFP) and the mixtures consisted of 10, 30 and 50% biodiesel in regular aviation fuel. The aviation fuel is a mixture of Jet A fuel + 5% Aeroshell 500 oil (called Ke) with the oil being added for turbo-engine’s lubrication. So, the used fuels were: Ke, Ke + 10% SFP, Ke + 30% SFP, Ke + 50% SFP. In first step, SFP was characterized in terms of: density, kinematic viscosity, flash and freezing points and calorific power. Also a deeper analysis was made by using FTIR for all the fuels involved in the experiments. The second step consisted of assessing the chemical reactions that occur during the burning process. Thus starting from the known elemental analysis, the air needed for a stoichiometric reaction has been calculated for each fuel mixtures. Also the resulting CO2 and water has been calculated from the reactions. The third step consisted of experimental testing the burning behavior of the above mentioned fuels on a micro turbo-engine. The used engine was Jet Cat P80® provided by Gunt Hamburg, Barsbüttel, Germany. The variation of: rpm vs. time, burning temperature vs. time and fuel debit vs. rpm are presented for starting and yield procedures. The tests have been conducted at 8 different working regimes of the engine. For each regime, an 1 min testing period was chose, during which burning temperature vs. rpm, fuel debit vs. rpm and thrust force vs. rpm were monitored. For maximum regime, only calculus for burning, thermal efficiencies and specific consumption have been made. As a main conclusion, the engine working behavior was steady throughout the entire range of rpm and for all the blends fed, thus the studied fuel blends may be considered as sustainable fuel for applications that are using micro turbo-engines with main advantages related to pollution and raw materials allowing the production of this type of fuel.

24 May 2021 in Metals
Verified
Journal Article
Open access
PDF file
RMRadu Mirea
Radu Mirea
IBIuliana Manuela Biris
Iuliana Manuela Biris
LCLaurentiu Constantin Ceatra
Laurentiu Constantin Ceatra
RERazvan Ene
Razvan Ene
APAlexandru Paraschiv
Alexandru Paraschiv
TBTeodor Adrian BADEA
Teodor Adrian BADEA
In this study, a CoCrMo-based metallic alloy was manufactured using a 3D-printing method with metallic powder and a laser-based 3D printer. The obtained material was immersed in a simulated body fluid (SBF) similar to blood plasma and kept 2 months at 37 °C and in relative motion against the SBF in order to mimic the real motion of body fluids against an implant. At determined time intervals (24, 72, 168, 336, and 1344 h), both the metallic sample and SBF were characterized from a physical-chemical point of view in order to assess the alloy’s behaviour in the SBF. Firstly, the CoCrMo based metallic sample was characterized by scanning electron microscopy (SEM) for assessing surface corrosion and X-ray diffraction (XRD) for determining if and/or what kind of spontaneous protective layer was formed on the surface; secondly, the SBF was characterized by pH, electrical conductivity (EC), and inductively coupled plasma mass spectroscopy (ICP-MS) for assessing the metal ion release. We determined that a 3D-printed CoCrMo alloy does not represent a potential biological hazard in terms of the concentration of metal ion releases, since it forms, in a relatively short period of time, a protective CoCr layer on its exposed surface.

8 June 2022 in Materials
Verified
Journal Article
Open access
PDF file
TBTeodor Adrian BADEA
Teodor Adrian BADEA
DBDan Batalu
Dan Batalu
NCNICOLAE CONSTANTIN
NICOLAE CONSTANTIN
APAlexandru Paraschiv
Alexandru Paraschiv
Delia PatroiDelia Patroi
Delia Patroi
LCLaurentiu Constantin Ceatra
Laurentiu Constantin Ceatra
Inconel 625 samples, obtained by Selective Laser Melting (SLM) and conventional technology, were tested for hot corrosion resistance against a molten mixture of Na2SO4 and V2O5. The assessments were performed in air, at 900 °C with exposure time of up to 96 h, and at 1000 °C for 8 h. Weight gain was higher for samples obtained by SLM, with 37.4% after 8 h, 3.98% after 24 h, 4.46% after 48 h, and 5.8% after 96 h at 900 °C (22.6% at 1000 °C, 8 h). Three stages of corrosion were observed, the first and last with a high corrosion rate, while the second one showed a slower corrosion rate. Corrosion behaviour depends on the morphology of the grain boundary, which can influence the infiltration of corrosive salts, and on the formation of Cr2NiO4 compound, which acts as a temporary barrier.

24 May 2021 in Materials
Verified
Journal Article
Open access
PDF file
RMRadu Mirea
Radu Mirea
ACAndrei Tiberiu Cucuruz
Andrei Tiberiu Cucuruz
LCLaurentiu Constantin Ceatra
Laurentiu Constantin Ceatra
TBTeodor Adrian BADEA
Teodor Adrian BADEA
IBIuliana Biris
Iuliana Biris
MCMihaiella Cretu
Mihaiella Cretu
Invitro experiments have been conducted on metallic biomaterials used for orthopedic implants in order to determine their behavior when immersed in simulated body fluid (SBF). Thus, 3Ti-based metallic biomaterial samples already available on the marked were purchased and immersed in simulated blood plasma, and kept at 37 °C for 4 months. In-depth characterization consisted of a wide series of structural characterizations of both the samples and SBF. Sample analysis consisted of the following: optical (OM) and scanning electron microscopy (SEM) in order to establish the surface and deep corrosion, mass gain/loss assessment for determining the metallic ions loss and/or protective layer formation, and X-ray diffraction in order to establish if and what kind of layers are formed. SBF analysis consisted of using inductively coupled plasma mass spectroscopy (ICP-MS) in order to establish if and/or how many metallic ions have dissociated from the metallic samples into the SBF, and measurements of pH and electrical conductivity. The key findings of the research are as follows: during the four months while kept in SBF, the samples show surface corrosion degradation and protective layer generation. Also, the amount of metallic ions dissociated into the SBF is making them suitable for use. Taking into account that it is highly improbable for such a large area of metal as the one considered within this work to be exposed to real body fluids and that all the samples have developed protective oxide films, the overall conclusion is that they are appropriate for implant use.