Stable and high surface area zirconium oxide nanoparticles have been synthesised by means of the hydrothermal method. The Brunauer–Emmett–Teller results show that a high surface area of 543 m2/g was...

Regional mechanics of the heart is vital in the development of accurate computational models for the pursuit of relevant therapies. Challenges related to heart dysfunctioning are the most important sources of mortality in the world. For example, myocardial infarction (MI) is the foremost killer in sub-Saharan African countries. Mechanical characterisation plays an important role in achieving accurate material behaviour. Material behaviour and constitutive modelling are essential for accurate development of computational models. The biaxial test data was utilised to generated Fung constitutive model material parameters of specific region of the pig myocardium. Also, Choi-Vito constitutive model material parameters were also determined in various myocardia regions. In most cases previously, the mechanical properties of the heart myocardium were assumed to be homogeneous. Most of the computational models developed have assumed that the all three heart regions exhibit similar mechanical properties. Hence, the main objective of this paper is to determine the mechanical material properties of healthy porcine myocardium in three regions, namely left ventricle (LV), mid-wall/interventricular septum (MDW) and right ventricle (RV). The biomechanical properties of the pig heart RV, LV and MDW were characterised using biaxial testing. The biaxial tests show the pig heart myocardium behaves non-linearly, heterogeneously and anisotropically. In this study, it was shown that RV, LV and MDW may exhibit slightly different mechanical properties. Material parameters of two selected constitutive models here may be helpful in regional tissue mechanics, especially for the understanding of various heart diseases and development of new therapies.

Membranes are widely used daily, such as for filtration in reverse osmosis, or in the form of electrolyte membrane fuel cells. Modified Nafion^® membranes were synthesised by impregnation and their mechanical properties were observed. The effect of the incorporation of a ZrO₂-CNT nano-filler within Nafion^® membrane on the thermal stability and crystallinity was investigated by TGA and XRD. Tensile test results show the increases in the mechanical properties of Nafion^® 117 membranes impregnated with ZrO₂-CNT when compared with that of commercial Nafion^® 117 membranes. The results also show that adding ZrO₂-CNT in Nafion^® 117 membranes improves the water contact angle and water uptake, as it enhances water retention within the membrane. The SEM results indicated that ZrO₂-CNT was well distributed in the Nafion^® 117 membrane pores through the impregnation method.

To investigate the effect of acidic nanoparticles on proton conductivity, permeability, and fuel-cell performance, a commercial Nafion^® 117 membrane was impregnated with zirconium phosphates (ZrP) and sulfated zirconium (S-ZrO₂) nanoparticles. As they are more stable than other solid superacids, sulfated metal oxides have been the subject of intensive research. Meanwhile, hydrophilic, proton-conducting inorganic acids such as zirconium phosphate (ZrP) have been used to modify the Nafion^® membrane due to their hydrophilic nature, proton-conducting material, very low toxicity, low cost, and stability in a hydrogen/oxygen atmosphere. A tensile test, water uptake, methanol crossover, Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), thermal gravimetric analysis (TGA), and scanning electron microscopy (SEM) were used to assess the capacity of nanocomposite membranes to function in a fuel cell. The modified Nafion^® membrane had a higher water uptake and a lower water content angle than the commercial Nafion^® 117 membrane, indicating that it has a greater impact on conductivity. Under strain rates of 40, 30, and 20 mm/min, the nanocomposite membranes demonstrated more stable thermal deterioration and higher mechanical strength, which offers tremendous promise for fuel-cell applications. When compared to 0.113 S/cm and 0.013 S/cm, respectively, of commercial Nafion^® 117 and Nafion^® ZrP membranes, the modified Nafion^® membrane with ammonia sulphate acid had the highest proton conductivity of 7.891 S/cm. When tested using a direct single-cell methanol fuel cell, it also had the highest power density of 183 mW cm⁻² which is better than commercial Nafion^® 117 and Nafion^® ZrP membranes.

The purpose of this study is to identify the steps involved in fabricating silica/chitosan composite membranes and their suitability for fuel cell applications. It also intends to identify the physical characteristics of chitosan composite membranes, including their degree of water absorption, proton conductivity, methanol permeability, and functional groups. In this investigation, composite membranes were fabricated using the solution casting method with a chitosan content of 5 g and silica dosage variations of 2% and 4% while stirring at a constant speed for 2 h. According to the findings, the analysis of composite membranes produced chitosan membranes that were successfully modified with silica. The optimum membrane was found to be 4% s-SiO₂ from the Sol-gel method with the composite membrane’s optimal condition of 0.234 cm/s proton conductivity, water uptake of 56.21%, and reduced methanol permeability of 0.99 × 10⁻⁷ cm²/s in the first 30 min and 3.31 × 10⁻⁷ in the last 150 min. Maintaining lower water uptake capacity at higher silica content is still a challenge that needs to be addressed. In conclusion, the fabricated membranes showed exceptional results in terms of proton conductivity and methanol permeability.

High quality computational model of soft tissues is a function of accurate and reliable mechanical properties. Hyperelastic constitutive models are normally utilised in developing reliable computational models. Therefore, section of proper and reliable constitutive models for soft tissue is critical. This work presents the biomechanical properties of oesophagus subjected to biaxial mechanical tensile test. Additionally, six hyperelastic constitutive models commonly used for modelling behaviour of soft tissues were selected. The experimental data were then fitted on Fung, Choi-Vito, Holzapfel (2000), Holzapfel (2005), Polynomial (Anisotropic) and Four-Fiber Family hyperelastic constitutive models. The sheep oesophagus subjected to equi-biaxial tension has exhibited different stress magnitude in both longitudinal and circumferential directions. There is significant difference between circumferential and longitudinal stresses (p = 0.0034). The average circumferential and longitudinal stresses are recorded to be 82.87 ± 30.36 kPa and 41.42 ± 32.02 kPa, respectively (p = 0.0034). Between six hyperelastic constitutive models, it was observed that Four-Fiber model has produced better fit when compared to others. After fitting biaxial mechanical properties of oesophagus, it was found that the Four-fiber family hyperelastic constitutive model would best fit.