Aniello Pelella

Dr. Aniello Pelella

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 May 2019 in Advanced Functional Materials
Verified
Journal Article
Closed access
PDF file
Antonio Di BartolomeoAntonio Di Bartolomeo
Antonio Di Bartolomeo
APAniello Pelella
Aniello Pelella
XLXiaowei Liu
Xiaowei Liu
FMFeng Miao
Feng Miao
Maurizio PassacantandoMaurizio Passacantando
Maurizio Passacantando
SLShi‐Jun Liang
Shi‐Jun Liang

3 August 2021 in Advanced Functional Materials
Verified
Journal Article
Open access
PDF file
AGAlessandro Grillo
Alessandro Grillo
Enver FaellaEnver Faella
Enver Faella
APAniello Pelella
Aniello Pelella
Filippo GiubileoFilippo Giubileo
Filippo Giubileo
Lida AnsariLida Ansari
Lida Ansari
Antonio Di BartolomeoAntonio Di Bartolomeo
Antonio Di Bartolomeo
Platinum diselenide (PtSe2) field‐effect transistors with ultrathin channel regions exhibit p‐type electrical conductivity that is sensitive to temperature and environmental pressure. Exposure to a supercontinuum white light source reveals that positive and negative photoconductivity coexists in the same device. The dominance of one type of photoconductivity over the other is controlled by environmental pressure. Indeed, positive photoconductivity observed in high vacuum converts to negative photoconductivity when the pressure is raised. Density functional theory calculations confirm that physisorbed oxygen molecules on the PtSe2 surface act as acceptors. The desorption of oxygen molecules from the surface, caused by light irradiation, leads to decreased carrier concentration in the channel conductivity. The understanding of the charge transfer occurring between the physisorbed oxygen molecules and the PtSe2 film provides an effective route for modulating the density of carriers and the optical properties of the material.

28 September 2021 in ACS Applied Materials & Interfaces
Verified
Journal Article
Open access
APAniello Pelella
Aniello Pelella
AGAlessandro Grillo
Alessandro Grillo
EFEnver Faella
Enver Faella
GLGiuseppe Luongo
Giuseppe Luongo
MAMohammad Bagher Askari
Mohammad Bagher Askari
Antonio Di BartolomeoAntonio Di Bartolomeo
Antonio Di Bartolomeo
The fabrication of a graphene–silicon (Gr-Si) junction involves the formation of a parallel metal–insulator–semiconductor (MIS) structure, which is often disregarded but plays an important role in the optoelectronic properties of the device. In this work, the transfer of graphene onto a patterned n-type Si substrate, covered by Si3N4, produces a Gr-Si device, in which the parallel MIS consists of a Gr-Si3N4-Si structure surrounding the Gr-Si junction. The Gr-Si device exhibits rectifying behavior with a rectification ratio up to 104. The investigation of its temperature behavior is necessary to accurately estimate the Schottky barrier height (SBH) at zero bias, φb0 = 0.24 eV, the effective Richardson’s constant, A* = 7 × 10–10 AK–2 cm–2, and the diode ideality factor n = 2.66 of the Gr-Si junction. The device is operated as a photodetector in both photocurrent and photovoltage mode in the visible and infrared (IR) spectral regions. A responsivity of up to 350 mA/W and an external quantum efficiency (EQE) of up to 75% are achieved in the 500–1200 nm wavelength range. Decreases in responsivity to 0.4 mA/W and EQE to 0.03% are observed above 1200 nm, which is in the IR region beyond the silicon optical band gap, in which photoexcitation is driven by graphene. Finally, a model based on two parallel and opposite diodes, one for the Gr-Si junction and the other for the Gr-Si3N4-Si MIS structure, is proposed to explain the electrical behavior of the Gr-Si device.

6 August 2020 in Small
Verified
Journal Article
Closed access
AGAlessandro Grillo
Alessandro Grillo
Maurizio PassacantandoMaurizio Passacantando
Maurizio Passacantando
Alla ZakAlla Zak
Alla Zak
APAniello Pelella
Aniello Pelella
Antonio Di BartolomeoAntonio Di Bartolomeo
Antonio Di Bartolomeo

20 May 2020 in Advanced Electronic Materials
Verified
Journal Article
Closed access
PDF file
Antonio Di BartolomeoAntonio Di Bartolomeo
Antonio Di Bartolomeo
APAniello Pelella
Aniello Pelella
Francesca UrbanFrancesca Urban
Francesca Urban
AGAlessandro Grillo
Alessandro Grillo
LILaura Iemmo
Laura Iemmo
Filippo GiubileoFilippo Giubileo
Filippo Giubileo

10 August 2020 in ACS Applied Materials & Interfaces
Verified
Journal Article
Open access
APAniello Pelella
Aniello Pelella
OKOsamah Kharsah
Osamah Kharsah
AGAlessandro Grillo
Alessandro Grillo
Francesca UrbanFrancesca Urban
Francesca Urban
Maurizio PassacantandoMaurizio Passacantando
Maurizio Passacantando
Antonio Di BartolomeoAntonio Di Bartolomeo
Antonio Di Bartolomeo
Metal contacts play a fundamental role in nanoscale devices. In this work, Schottky metal contacts in monolayer molybdenum disulfide (MoS2) field-effect transistors (FETs) are investigated under electron beam irradiation. It is shown that the exposure of Ti/Au source/drain electrodes to an electron beam reduces the contact resistance and improves the transistor performance. The electron beam conditioning of contacts is permanent, while the irradiation of the channel can produce transient effects. It is demonstrated that irradiation lowers the Schottky barrier at the contacts, due to thermally induced atom diffusion and interfacial reactions. The simulation of electron paths in the device reveals that most of the beam energy is absorbed in the metal contacts. The study demonstrates that electron beam irradiation can be effectively used for contact improvement though local annealing.