The existence of karst caves poses a large threat to safe tunnel construction in a karst area. This paper presents a synthetic method to evaluate the collapse risk before subway tunnel construction with Yang‐Jian interval tunnel as a case study. The crosshole seismic Computed Tomography (CT) integrated with Geological Drilling (Geo‐D) was first applied to accurately delineate the karst location and its scale. Then, 483 groups of seismic wave CT images were recorded, and 524 karst cave anomalies were found. The height of karst caves in the study area is 1–20 m and mainly concentrated at approximately 5 m. The vertical distance between the karst cave and the tunnel is mainly within 15 m. According to the detection results, a series of numerical models were built and calculated using FLAC3D to investigate the effect of different sizes and locations of karst caves on the displacement and stability of the surrounding rock in tunnels. Afterwards, based on the simulation results, the disturbance degree evaluation index was established to quantitatively evaluate the risk level of karst caves. The evaluation results indicate that the buried depth of the karst cave greatly affects the disturbance degree. No treatment is required for the deeply buried karst cave that is more than 7 m from the tunnel. When the distance between the cave and the tunnel is less than 7 m, there is a critical size of the cave. Karst caves that are larger than that critical value must be filled with a single slurry or binary slurry before tunnel construction to eliminate the risk of tunnel collapse. This study can be used to provide a more efficient and economical program for metro tunnel construction above a karst cave.
To explore the characteristics of rock deformation and failure under cyclic loading and unloading, the MTS815 rock mechanics test system and acoustic emission (AE) signal acquisition system were used to perform cyclic loading and unloading tests on red sandstone samples. The results showed that, compared with the uniaxial compression test, cyclic loading and unloading had a certain strengthening effect on the strength of the samples. The plastic deformation of the rock samples increased as the number of cycles increased. Based on AE signals, the cracking mode classification was analyzed on the basis of the average frequency and the rise angle of the waveforms. It was observed that the Felicity ratio gradually decreased with the increase in the stress level, which showed a cumulative damage effect. From the perspective of energy, the obvious increase of AE energy rate was mainly concentrated in the early and late stages of uniaxial compression, while the significant increase of dissipated energy rate occurred in the late stage of uniaxial compression. During the cyclic loading and unloading, most of the work done by external forces in the compaction stage and the elastic stage was converted into elastic strain energy, and dissipated energy began to gradually increase in the stage of stable fracture development. In addition, it was found that the damage evolution of the rock samples changed from slow to fast, and the dissipated energy ratio increased when failure was approaching.
To explore the influence of bedding structure on mechanical properties and failure mechanism of anisotropic rocks, six stratified sandstone specimens with different bedding orientations were tested by uniaxial static and cyclic loading. Acoustic emission (AE) and digital image correlation (DIC) were exploited to analyze the mechanism of crack initiation and propagation. The results show that with the increase of the bedding orientation, the peak strength of the stratified sandstone decreases first and then increases, behaving an obvious anisotropic characteristic. The AE characteristic-stress-strain curve can be divided into four stages: crack closure stage, linear elastic deformation stage, stable crack growth stage, and unstable crack growth stage. Moreover, as the bedding orientation increases from 30° to 90°, the crack closure stage gradually lengthens, while the linear elastic deformation stage first shortens and then lengthens. Under uniaxial static compression, due to the presence of bedding surface, the rock surface has a relative slip trend as a result of the uneven distribution of strain on the left and right parts, and the strain field boundary is almost consistent with the bedding orientation. Furthermore, cyclic loading can increase the rock stiffness, and the stain field boundary of 60° stratified sandstone sample in each cycle is slightly different in the cyclic loading.
The construction of super large section (SLS) shallow buried tunnels involves challenges related to their large span, high flat rate, and complex construction process. Selecting an appropriate excavation method is crucial for ensuring stability, controlling costs, and managing the construction timeline. This study focuses on the selection of excavation methods and the mechanical responses of SLS tunnels in different types of surrounding rock. The research is based on the Yangjiashan tunnel project in Zhejiang Province, China, which is a four-line highway tunnel with a span of 21.3 m. Three sequential excavation methods were proposed and simulated using the three-dimensional finite difference method: the “upper first and lower later” side drift (SD) method, the central diaphragm method, and the top heading and bench (HB) method. The mechanical response characteristics of tunnel construction under these methods were investigated, including rock deformation, rock pressure, and the internal forces acting on the primary support. By comparing the performance of the three construction methods in rock masses of Grades III to V, the study aimed to determine the optimal construction method for SLS tunnels considering factors such as safety, cost, and schedule. Field tests were conducted to evaluate the effectiveness of the optimized construction scheme. The results of the field monitoring indicated that the “upper first and lower later” SD method in Grade V rock mass and the HB method in Grade III to IV rock mass are feasible and cost-effective under certain conditions. The research findings provide valuable insights for the design and construction of SLS tunnels in complex conditions, serving as a reference for engineers and project managers.
Liquid nitrogen (LN2), which can greatly improve the efficiency of hot dry rock (HDR) mining, is commonly used as a cooling material in the enhanced geothermal system (EGS). Physical property, triaxial compression, and permeability tests were undertaken on treated granite samples, for a better scientific understanding of the effect of the LN2 cooling method on the mechanical and permeability properties of the rocks after heat treatment. The experimental results indicated that the physical properties of the treated granite change significantly, such as the density and wave velocity are substantially reduced. Meanwhile, with the increase of treatment temperature, the macroscopic cracks on its surface are gradually generated and the volume is expanded clearly. In addition, the surface wettability of granite gradually increases with increasing temperature. Compared with the air/water cooling methods, under LN2 cooling condition, the mechanical properties decrease markedly. When the temperature exceeds 600C, the granite strength decreases significantly to only 56.16 of the reference value. The deformation properties also change significantly, with a final strain of about 3 at failure for a sample at 800C, showing an obvious ductile deformation characteristic. Further, an appreciable correlation also exists between the initial permeability of granite and temperature. Once the temperature exceeds 200C, the increase in temperature contributes to the increase in initial permeability. In addition to the effect of temperature, the increase in load also leads to a change in the permeability coefficient. When the temperature reaches 600C, the permeability of granite first decreases and then increases with the increases in axial stress. The results of this paper are valuable in understanding the effect of thermal shock by LN2 on the fracturing efficiency and permeability characteristics of dry hot rocks.