To date, little attention has been given to remote sensing-based algorithms for inferring urban surface evapotranspiration. A multi-source parallel model based on ASTER data was one of the first examples, but its accuracy can be improved. We therefore present a modified multi-source parallel model in this study, which has made improvements in parameterization and model accuracy. The new features of our modified model are: (1) a characterization of spectrally heterogeneous urban impervious surfaces using two endmembers (high- and low-albedo urban impervious surface), instead of a single endmember, in linear spectral mixture analysis; (2) inclusion of an algorithm for deriving roughness length for each land surface component in order to better approximate to the actual land surface characteristic; and (3) a novel algorithm for calculating the component net radiant flux with a full consideration of the fraction and the characteristics of each land surface component. HJ-1 and ASTER data from the Chinese city of Hefei were used to test our model’s result with the China–ASEAN ET product. The sensitivity of the model to vegetation and soil fractions was analyzed and the applicability of the model was tested in another built-up area in the central Chinese city of Wuhan. We conclude that our modified model outperforms the initial multi-source parallel model in accuracy. It can obtain the highest accuracy when applied to vegetation-dominated (vegetation proportion > 50%) areas. Sensitivity analysis shows that vegetation and soil fractions are two important parameters that can affect the ET estimation. Our model is applicable to estimate evapotranspiration in other urban areas.

High-resolution gridded 2 m air temperature datasets are important input data for global and regional climate change studies, agrohydrologic model simulations and numerical weather predictions, etc. In this study, the digital elevation model (DEM) is used to correct temperature forecasts produced by ECMWF. The multi-grid variation formulation method is then used to fuse the data from corrected temperature forecasts and ground automatic station observations. The fused dataset covers the area over (0–60°N, 70–140°S), where different underlying surfaces exist, such as plains, basins, plateaus, and mountains. The spatial and temporal resolutions are 1 km and 1 h, respectively. The comparison of the fusion data with the verification observations, including 2400 weather stations, indicates that the accuracy of the gridded temperature is superior to European Centre for Medium-Range Weather Forecasts (ECMWF) data. This is because a more significant number of stations and high-resolution terrain data are used to generate the fusion data than are utilized in the ECMWF. The obtained dataset can describe the temperature feature of peaks and valleys more precisely. Due to its continuous temporal coverage and consistent quality, the fusion dataset is one of China’s most widely used temperature datasets. However, data uncertainty will increase for areas with sparse observations and high mountains, and we must be cautious when using data from these areas.

Optimum interpolation (OI) analysis is performed on the sea surface temperature (SST) products retrieved from the Fengyun-3C (FY-3C) visible and infrared radiometer (VIRR). The oriented elliptic correlation scale is employed on the SST data and then compared with those from the traditional rectangular correlation scale in the OI analysis. The results were also evaluated against the daily SST data from the in-situ buoys and the Reynolds Optimum Interpolation 1/4 Degree Daily SST (OISST) during 2015. The statistical metrics indicate that the SSTs determined using the oriented elliptic correlation scales have higher accuracy than those from rectangular correlation scales, as the root-mean-square error (RMSE) from 0.42°C to 0.38°C, which are higher than those obtained with the comparison with OISST (RMSE of 0.28°C). This assessment demonstrates that the original SST data from FY-3C VIRR are of poor quality due to the presence of unresolved errors, whereas the oriented elliptic correlation scales for SST demonstrate better performance than the rectangular correlation scales in the OI analysis.

Sea surface temperature (SST) is critical for global climate change analysis and research. In this study, we used visible and infrared scanning radiometer (VIRR) sea surface temperature (SST) data from the Fengyun-3C (FY-3C) satellite for SST analysis, and applied the Kalman filtering methods with oriented elliptic correlation scales to construct SST fields. Firstly, the model for the oriented elliptic correlation scale was established for SST analysis. Secondly, observation errors from each type of SST data source were estimated using the optimal matched datasets, and background field errors were calculated using the model of oriented elliptic correlation scale. Finally, the blended SST analysis product was obtained using the Kalman filtering method, then the SST fields using the optimum interpolation (OI) method were chosen for comparison to validate results. The quality analysis for 2016 revealed that the Kalman analysis with a root-mean-square error (RMSE) of 0.3243 °C had better performance than did the OI analysis with a RMSE of 0.3911 °C, which was closer to the OISST product RMSE of 0.2897 °C. The results demonstrated that the Kalman filtering method with dynamic observation error and background error estimation was significantly superior to the OI method in SST analysis for FY-3C SST data.