Wireless broadband access networks have been positioning themselves as a good solution for manufacturers and users of IoT (internet of things) devices, due mainly to the high data transfer rate required over terminal devices without restriction of information format. In this work, a review of two Radio over Fiber strategies is presented. Both have excellent performance and even offer the possibility to extend wireless area coverage where mobile networks do not reach or the 802.11 network presents issues. Radio Frequency over Fiber (RFoF) and intermediate Frequency over Fiber (IFoF) are two transmission strategies compatible with the required new broadband services and both play a key role in the design of the next generation integrated optical–wireless networks, such as 5G and Satcom networks, including on RAU (Remote Antenna Unit) new functionalities to improve their physical dimensions, employing a microelectronic layout over nanometric technologies.

This paper presents the design of a new phase shifter to be used in a receiver of active antenna array operating in the range from 17 GHz to 22 GHz. Beamforming is achieved by controlling the phase of the signal in each radiant element. In this context, the phase shift is obtained by the combination of a quadrature signal generator (QSG) and a variable gain amplifier (VGA). This work is focused on the design of a VGA which has a set of dummy transistors to keep the input and output impedance constant. The phase shifter is digitally programmable using a 5-bit word. The system was laid out using a 65 nm CMOS process, and the physical post-layout results show that the phase shifter achieves root mean square errors of 4.5° for the phase and 0.79 dB for the gain at a frequency of 19.5 GHz. A comparative analysis with other recently published phase shifters shows that the proposed phase shifter presents a good compromise between power consumption and accuracy.

In this work, we present a capacitance-to-voltage converter (CVC) for capacitive accelerometers based on microelectromechanical systems (MEMS). Based on a fully-differential transimpedance amplifier (TIA), it features a 34-dB transimpedance gain control and over one decade programmable bandwidth, from 75 kHz to 1.2 MHz. The TIA is aimed for low-cost low-power capacitive sensor applications. It has been designed in a standard 0.18-μm CMOS technology and its power consumption is only 54 μW. At the maximum transimpedance configuration, the TIA shows an equivalent input noise of 42 fA/ $\sqrt{\text{Hz}}$ at 50 kHz, which corresponds to 100 μg/ $\sqrt{\text{Hz}}$ .

This article presents an optimized design of a low-noise transimpedance amplifier (TIA) with high linearity for use in the downlink receiver of a remote antenna unit (RAU). The aim of this design is to be used in a cost-effective indoor distributed antenna system (DAS) for WLAN transmission using a mixed fiber-wireless system. The circuit topology consists of a fully differential shunt–shunt feedback TIA with digitally programmable transimpedance. An open-loop gain compensation technique is used to maintain stability and constant bandwidth (BW). The TIA has been fabricated in 65 nm CMOS technology with a 1.2 V voltage supply. The total power consumption of the TIA is 6 mW. A complete electrical and optical characterization with a 1550 nm PIN photodiode has been performed to demonstrate the reliable 54 Mb/s 802.11a WLAN transmission achieved with an error vector magnitude (EVM) lower than 3% for a 20 dB optical input range.

Equivalent time oscilloscopes are widely used as an alternative to real-time oscilloscopes when high timing resolution is needed. For their correct operation, they need the trigger signal to be accurately aligned to the incoming data, which is achieved by the use of a clock and data recovery circuit (CDR). In this paper, a new multilevel bang-bang phase detector (BBPD) for CDRs is presented; the proposed phase detection scheme disregards samples taken close to the data transitions for the calculation of the phase difference between the inputs, thus eliminating metastability, one of the main issues hindering the performance of BBPDs.

This letter presents a new complimentary metal-oxide-semiconductor analog continuous-time equalizer aimed to compensate the limited frequency response of step-index polymer optical fiber (SI-POF), a transmission medium very attractive for industrial applications as factory automation and process control networks because of its cost and immunity to electromagnetic interference. The structure overcomes the limitations of the most widely used continuous-time equalizer, the degenerated differential pair, for 1-V supply voltage. The linear equalizer has been proved for multigigabit short-range applications targeting up to 2 Gb/s through a 50-m SI-POF. The prototype consumes 2.7 mW.