Wireless broadband access networks have been positioning themselves as a good solution for manufacturers and users of IoT (internet of things) devices, due mainly to the high data transfer rate required over terminal devices without restriction of information format. In this work, a review of two Radio over Fiber strategies is presented. Both have excellent performance and even offer the possibility to extend wireless area coverage where mobile networks do not reach or the 802.11 network presents issues. Radio Frequency over Fiber (RFoF) and intermediate Frequency over Fiber (IFoF) are two transmission strategies compatible with the required new broadband services and both play a key role in the design of the next generation integrated optical–wireless networks, such as 5G and Satcom networks, including on RAU (Remote Antenna Unit) new functionalities to improve their physical dimensions, employing a microelectronic layout over nanometric technologies.

This article presents an optimized design of a low-noise transimpedance amplifier (TIA) with high linearity for use in the downlink receiver of a remote antenna unit (RAU). The aim of this design is to be used in a cost-effective indoor distributed antenna system (DAS) for WLAN transmission using a mixed fiber-wireless system. The circuit topology consists of a fully differential shunt–shunt feedback TIA with digitally programmable transimpedance. An open-loop gain compensation technique is used to maintain stability and constant bandwidth (BW). The TIA has been fabricated in 65 nm CMOS technology with a 1.2 V voltage supply. The total power consumption of the TIA is 6 mW. A complete electrical and optical characterization with a 1550 nm PIN photodiode has been performed to demonstrate the reliable 54 Mb/s 802.11a WLAN transmission achieved with an error vector magnitude (EVM) lower than 3% for a 20 dB optical input range.

In this work, we present a capacitance-to-voltage converter (CVC) for capacitive accelerometers based on microelectromechanical systems (MEMS). Based on a fully-differential transimpedance amplifier (TIA), it features a 34-dB transimpedance gain control and over one decade programmable bandwidth, from 75 kHz to 1.2 MHz. The TIA is aimed for low-cost low-power capacitive sensor applications. It has been designed in a standard 0.18-μm CMOS technology and its power consumption is only 54 μW. At the maximum transimpedance configuration, the TIA shows an equivalent input noise of 42 fA/ $\sqrt{\text{Hz}}$ at 50 kHz, which corresponds to 100 μg/ $\sqrt{\text{Hz}}$ .

This paper presents a novel design of a wideband circular polarization 2 × 2 microstrip antenna array working at Ka-band frequencies, from 27.5 to 31 GHz. This module is highly integrable with new silicon beamformer chips, creating a unit cell that can be part of a large electronically steerable antenna for compact, ultra-low-profile, Satcom-on-the-move (SOTM) platforms. A multi-layer structure fabricated in standard printed circuit board (PCB) technology with high-yield substrates has been used. The radiating elements consist of double-stacked circular patches housed in a cavity and fed by H-shaped aperture coupling. It achieves a bandwidth of 16.5 % with a wide beam-width of 95° in the desired band, which is necessary for wide scanning angles in a large phased array. In the 2 × 2 unit cell, the antenna elements are distributed by means of a sequential rotation technique where the separation between two of them is 5.3 mm in the XY-plane. Broadside beam-widths ranging from 53.4° at 27.5 GHz to 42.1° at 31 GHz are achieved, with boresight directivities from 10.7 to 12.9 dBi, respectively, in both the RHCP and LHCP polarization. Moreover, mutual coupling levels below −20 dB and an axial ratio less than 3 dB in the whole band guarantee a good circular polarization purity.

This letter presents a new complimentary metal-oxide-semiconductor analog continuous-time equalizer aimed to compensate the limited frequency response of step-index polymer optical fiber (SI-POF), a transmission medium very attractive for industrial applications as factory automation and process control networks because of its cost and immunity to electromagnetic interference. The structure overcomes the limitations of the most widely used continuous-time equalizer, the degenerated differential pair, for 1-V supply voltage. The linear equalizer has been proved for multigigabit short-range applications targeting up to 2 Gb/s through a 50-m SI-POF. The prototype consumes 2.7 mW.

In this work, a capacitance-to-voltage converter based on a fully-differential transimpedance amplifier (TIA) with programmable gain and bandwidth for MEMS accelerometers is presented. It is aimed for a differential surface-micromachined comb-finger capacitive accelerometer, but can be used in many other capacitive sensor applications. The TIA has been designed in a 180-nm CMOS technology and it achieves a minimum equivalent input noise of 42 fA/√Hz at 50 kHz, which corresponds to an acceleration noise of 100 μg/√Hz.