Complex (Mn, X)S compounds nucleated on Al2O3-based sites were found as the major nucleation sites for graphite flakes in both un- inoculated and inoculated grey irons. (Mn, X)S particles (1–8 fun) and their corresponding nuclei (0.1–2.7 μm) were characterized as size, morphological features and distribution patterns of different elements (Mn, S, Ca, Sr, Al, O, Fe), under the influence of inoculant type (HP-FeSi, Sr-FeSi, Ca-FeSi) and cooling rate (4.3 and 542°C/sec). These particles present so common features for all irons (distinct core; always Al and O presence in the core; Mn and S throughout the compound; usually high number, etc), but also the peculiar features (Ca presence throughout almost all compounds independent of inoculant type; Sr mainly in the core of Sr-FeSi treated iron; ovoid tendency of compounds in Ca-FeSi treated irons; lower nuclei size, lower Mn/S ratio in the compounds body and more complex (Mn,X)S compounds in inoculated irons, etc). More intricacy of (Mn, X)S compounds in inoculated irons leads to lower crystallographic misfit given the graphite (more favorable to graphite nucleation).
1 December 2010 in Materials Science and Technology
A three-stage model for the nucleation of graphite in grey irons has been proposed. Stage 1 involves formation of small oxide based sites (usually <2·0 μm) in the melt. Stage 2 involved precipitation of complex (Mn,X)S compounds (usually <5·0 μm) nucleated by stage 1 microinclusions. Finally, in stage 3, graphite nucleates on the sides of the (Mn,X)S compounds, which have low crystallographic misfit with graphite. Three groups of elements are important to sustain this sequence for effective graphite nucleation. These are strong deoxidising elements, such as Al and Zr, to form a high count of very small stage 1 microinclusions, Mn and S to sustain MnS type sulphide formation, and inoculating elements, which act in the first stage and/or in the second stage of the graphite nucleation sequence. Inoculating elements improve the capability of (Mn,X)S compounds to nucleate graphite. In inoculated irons, the (Mn,X)S compounds are more complex. They have a lower Mn/S ratio and higher capability to nucleate graphite, especially when preconditioning/inoculating elements contribute with a high count of effective stage 1 particles.
Ferritic high-Si ductile cast irons replace an unstable mixed ferrite-pearlite matrix with a unique combination of high elongation, strength and hardness (ideal for automotive drive train components) and resistance to oxidation and corrosion at high temperatures (automotive exhaust and turbocharger systems). The present paper analyses the graphite parameters of 4.5%Si, un-inoculated ductile cast iron (4.7%CE, 0.035%Mgres) as an effect of the casting section size. The structure is characterized by 10.5–11.2% graphite and 464–975 nodules/mm2, at more than 70% ferrite and no carbides, including at 3 mm wall thickness. The lower the wall thickness is, the higher the nodule count is and, consequently, the higher the ferrite amount is. The Roundness Graphite Shape Factor (RSF = 0.65–0.68) illustrates the presence of Slightly Irregular Spheroidal Graphite (Form V ISO 945). There is a big difference between the graphite nodularity evaluated according to ISO 16112:2017 [CGI] (NG1 = 79–86%) and according to ISO 945-4-2019 (DI) (NG2 = 65.2–74.6%), both of them based on RSF. Graphite Nodularity (NG3), calculated with the ISO 945-4-2019 [DI] formula, but replacing RSF with SSF, Sphericity Graphite Shape Factor, has an intermediary position. The higher the imposed minimum RSF or SSF is, the lower the Graphite Nodularity (NG4, NG5): 80–90% for min. 0.50 (minimum Form IV or Intermediate Graphite), 60–80% for min. 0.60–0.65 (minimum Form V graphite) and 35–70% for min. 0.80 (minimum Form VI graphite). The SSF is more representative than the RSF for Si-alloyed ductile cast iron, so it is recommended to use a graphite nodularity calculus considering SSF instead of the RSF formula (stipulated by ISO 945-4-2019), with SSF replacing RSF.
20 December 2011 in Journal of Thermal Analysis and Calorimetry