Christos Aneziris

Prof. Dr. Christos Aneziris

Institute of Ceramics, Refractories and Composite Materials, Technische Universität Bergakademie Freiberg, 09599 Freiberg, Germany

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 January 2023 in Ceramics
Verified
Journal Article
Open access
PDF file
KMKirsten Moritz
Kirsten Moritz
NBNora Brachhold
Nora Brachhold
JHJana Hubálková
Jana Hubálková
GSGert Schmidt
Gert Schmidt
CAChristos Aneziris
Christos Aneziris
The partial replacement of primary raw materials for the production of refractories with recycled ones gains in importance, as it contributes to the conservation of natural resources, energy saving, and reduction in greenhouse gas emissions. In this work, the use of a magnesia–carbon (MgO-C) recyclate in the fractions 3–6, 1–3, and 0–1 mm as a raw material for MgO-C refractories was investigated. The recyclate was examined via optical and scanning electron microscopy. Using mixtures with different recyclate contents up to 82 wt%, MgO-C specimens were prepared to study the influence of the recyclate on their chemical composition, structure, and properties. The substitution of primary raw materials with the recyclate did not cause a decrease in the MgO content analyzed after carbon burnout, but the contents of the individual impurities changed. A comparison of the MgO-C that contains 82 wt% recyclate with the recyclate-free material through computed tomography indicated a change in the size distribution of the MgO grains. The porosity increased, and the cold modulus of rupture decreased with increasing recyclate content, whereas the thermal shock resistance improved. At a recyclate content of 40 wt%, the refractoriness under load was only slightly lower than that of the recyclate-free material.

27 October 2021 in Materials
Verified
Journal Article
Open access
PDF file
Tilo ZienertTilo Zienert
Tilo Zienert
DEDirk Endler
Dirk Endler
JHJana Hubálková
Jana Hubálková
GGGökhan Günay
Gökhan Günay
Anja WeidnerAnja Weidner
Anja Weidner
CAChristos Aneziris
Christos Aneziris
Niobium-alumina aggregate fractions with particle sizes up to 3150 µm were produced by crushing pre-synthesised fine-grained composites. Phase separation with niobium enrichment in the aggregate class 45–500 µm was revealed by XRD/Rietveld analysis. To reduce the amount of carbon-based impurities, no organic additives were used for the castable mixtures, which resulted in water demands of approximately 27 vol.% for the fine- and coarse-grained castables. As a consequence, open porosities of 18% and 30% were determined for the fine- and coarse-grained composites, respectively. Due to increased porosity, the modulus of rupture at room temperature decreased from 52 MPa for the fine-grained composite to 11 MPa for the coarse-grained one. However, even the compressive yield strength decreased from 49 MPa to 18 MPa at 1300 °C for the fine-grained to the coarse-grained composite, the latter showed still plasticity with a strain up to 5%. The electrical conductivity of fine-grained composite samples was in the range between 40 and 60 S/cm, which is fifteen magnitudes above the values of pure corundum.

22 September 2021 in Materials
Verified
Journal Article
Open access
PDF file
ESEnrico Storti
Enrico Storti
MNMarc Neumann
Marc Neumann
Tilo ZienertTilo Zienert
Tilo Zienert
JHJana Hubálková
Jana Hubálková
CAChristos Aneziris
Christos Aneziris
Full metal-ceramic composite beads containing different amounts of niobium and alumina, particularly 100 vol% alumina, 100 vol% niobium, and 95/5 vol% niobium/alumina, were produced by the alginate gelation process. The suspension for bead fabrication contained sodium alginate as gelling agent and was added dropwise into a calcium chloride solution to trigger the consolidation process. After debinding in air, sintering of the composite beads was performed under inert atmosphere. Samples in green and sintered state were analyzed by digital light microscopy and scanning electron microscopy equipped with energy dispersive X-ray spectroscopy. Investigations by mercury intrusion porosimetry revealed that pure alumina beads featured smaller pores compared to composite beads, although the open porosities were comparable. The fracture strength was evaluated on single beads. Contrary to the pure alumina, the composite beads showed a clear plastic deformation. Pure niobium beads showed a ductile behavior with very large deformations. XRD analyses revealed the presence of calcium hexaluminate and beta-alumina as minor phases in the alumina beads, while the composite ones contained about 25 wt% of impurities. The impurities comprised NbO arising from the oxidation, and β-Nb2C, from the reaction with the residual sodium alginate.

14 December 2021 in Metals
Verified
Journal Article
Open access
PDF file
XWxingwen wei
xingwen wei
SDSteffen Dudczig
Steffen Dudczig
DCDmitry Chebykin
Dmitry Chebykin
CAChristos Aneziris
Christos Aneziris
Olena VolkovaOlena Volkova
Olena Volkova
In the previous research works, ZnAl2O4 material was considered as one of the solutions for the decopperization process of molten steels; up to 33% of decopperization efficiency was reported by utilising the ZnAl2O4 filter. In order to verify the decopperization possibility of ZnAl2O4 materials, iron-based alloys with various copper and carbon contents were interacted with ZnAl2O4 substrates in a heating microscope under an argon gas atmosphere at 1600 °C. Fe-Cu alloys were found to react with the ZnAl2O4 substrate during the interaction process, and a reaction layer with a complex composition around the alloy droplet was formed; however, Cu was not detected in the reaction layer. Cu was later found infiltrated inside of the ZnAl2O4 substrates. Furthermore, the Cu-Zn compounds were detected when the copper content in Fe-Cu alloys was 10 wt% Cu. After interaction experiments, copper was decreased in all cases. Thereby, the copper evaporation and infiltration into the ZnAl2O4 substrate were considered as the reasons for copper loss. Moreover, oxygen dissolved in melt was found to have a great effect on the copper evaporation process.

7 February 2023 in Ceramics
Verified
Journal Article
Open access
PDF file
SYSerhii Yaroshevskyi
Serhii Yaroshevskyi
PMPiotr Malczyk
Piotr Malczyk
CWChristian Weigelt
Christian Weigelt
JHJana Hubálková
Jana Hubálková
SDSteffen Dudczig
Steffen Dudczig
CAChristos Aneziris
Christos Aneziris
Three-dimensionally printed fine-grained refractory ceramics ready for use in contact with liquid steel based on developed one-step thermal debindable ceramic filaments that do not require any chemical solvent pre-debinding are investigated. This work exhibits the most favourable debinding and sintering regimes with an excellent form stability and reproducibility of printed products ensured. The structure of the sintered products was examined with computed tomography. The designed inner geometry with micro-porosity introduced during debinding combined with pre-designed printed macro-cavities enabled the outstanding thermal-shock performance of the specimens. The functionality of the sintered refractory products in the form of casting nozzles was preliminarily tested in contact with steel melt using a hot-stage microscope. The structure of the specimen was subsequently examined with laser scanning microscopy and scanning electron microscopy. The mechanical properties of printed samples were studied via mercury intrusion porosimetry, compressive strength testing, and spatial tensile strength testing. According to the results, the cold crushing strength of the 3D-printed specimens in the printing direction was comparable to that of pressed fine-grained alumina specimens (50–60 MPa). The measured porosity was 21.5 vol% with a pore size less than 10 µm, which is suitable for applications in contact with molten steel. In order to show thermal-shock resistance of the 3D-printed casting nozzle, a 100 kg steel-melt flow test was performed in a steel-casting simulator with the nozzle surviving all related thermal shocks as well as the ferrostatic pressure of the melt. The evaluated composition and production route of the filaments can be utilized to produce one-step, thermally debindable, thermal-shock-resistant refractory parts with a complex inner structure that are applicable in an industrial environment.

29 April 2023 in Crystals
Verified
Journal Article
Open access
PDF file
Tilo ZienertTilo Zienert
Tilo Zienert
CAChristos Aneziris
Christos Aneziris
The transition aluminas δ1 and the cubic, non-spinel-type η-Al2O3 were detected in addition to α-Al2O3 in flame-sprayed material. Their transitions from room temperature up to 1200 °C were investigated by high-temperature XRD measurements. Structural changes with time and temperature were observed for all transition aluminas (η-, δ1- and θ-Al2O3). The phases followed the expected transition sequence of η→δ1→θ→α and showed mainly linear, temperature-independent transition rates. Based on the determined thermal expansion of the phases, it is proposed that the metastable transitions are at least partly mechanically induced. In addition, a second-order phase transition from η→θ might be indicated around 1050–1075 °C by the determined trends of density.