Multiphase systems provides benefits compared to three-phase systems, such as improved torque per ampere, high power density, better fault tolerance, lower current per phase (due to power-splitting among a higher number of phases), and lower torque ripple, among others. Depending on the application, the system must meet determined requirements, such as the presence of harmonic content, power losses, and common-mode voltage (CMV) generation. This paper presents a comparative analysis of space vector modulation (SVM) techniques applied to a five-phase voltage source inverter with SiC switches to provide an overview of their performance. The performance of five-phase 2L SVPWM (space vector pulse width modulation), 2L+2M SVPWM, 4L SVPWM techniques, and their discontinuous versions, are analyzed by focusing on harmonic content, power losses, and CMV generation using SiC semiconductor devices. Matlab/Simulink and PLECS simulations are performed to achieve the above mentioned goal. The use of different techniques allows (1) reducing the harmonic distortion when 2L+2M SVPWM and 4L SVPWM are applied, and (2) the switching sequence of the modulation techniques can influence the switching losses. Therefore, the use of SiC switches reduces the switching losses. (3) However, CMV dv/dt increases. Therefore, it is possible to minimize the effects of the CMV dv/dt and amplitude by choosing the adequate technique.
3 May 2022 in IEEE Transactions on Industrial Electronics
This article proposes and studies different sigma–delta ( $\Sigma$$\Delta$ ) modulation strategies for obtaining a constant common-mode voltage (CMV) by eliminating the CMV level transitions in a five-phase voltage source inverter (VSI). These techniques are based on choosing vectors that generate a constant CMV with values of 0.1 $V_{\text{dc}}$ or –0.1 $V_{\text{dc}}$ . Because of the high-switching frequencies used with wide-bandgap semiconductors, pulse-width modulation techniques continually generate high d v /d t values. Therefore, the proposal to combine a $\Sigma$$\Delta$ modulation strategy with vector selections achieves a constant CMV level due to the elimination of its level transitions, a reduction in conducted electromagnetic interference and a high-efficiency converter operation. The average number of switching per transistor of the VSI is analyzed using the results from MATLAB/Simulink and PLECS simulations. Experimental results are obtained by applying the proposed $\Sigma$$\Delta$ modulation strategies on a VSI with silicon carbide MOSFETs. The results demonstrate the achievement of the aforementioned features.
20 October 2021 in IEEE Transactions on Power Electronics
This article proposes a new modulation strategy for a five-phase high-frequency voltage source inverter (VSI) based on sigma–delta ( $\Sigma \Delta$ ) modulators. This modulation strategy of five-phase large–medium-zero vectors $\Sigma \Delta$ (5P-LMZV- $\Sigma \Delta$ ) applies the same switching states as the two large and two medium space vector modulation (2L+2M SVM). Because $\Sigma \Delta$ modulations are designed to operate at high switching frequencies, using wide-bandgap devices, therefore, improves the efficiency of the VSI, despite its operating at these high switching frequencies. We analyze the use of single-loop and double-loop $\Sigma \Delta$ modulators (SL-5P-LMZV- $\Sigma \Delta$ and DL-5P-LMZV- $\Sigma \Delta$ , respectively), and additionally modify the proposed modulation strategy to use all the vectors in order to analyze the effects from applying small vectors. The proposed modulation techniques allow minimizing switching losses due to the reduced switching operations, mitigating low-order harmonics, decreasing the amplitude of high-frequency harmonics, and reducing common-mode voltage dv/dt transitions. We analyze the performance of the proposed modulation technique using MATLAB/Simulink and PLECS, and then compare it with 2L+2M SVM. Using a VSI with silicon carbide mosfet , we obtained our experimental results demonstrating these characteristics, by which we conclude that our proposed strategy is an improvement over 2L+2M SVM.
5 May 2022 in IEEE Transactions on Power Electronics
Various sigma–delta ( $\Sigma$$\Delta$ ) modulation techniques for reducing the maximum peak-to-peak amplitude of common-mode voltage (CMV) by 80% in a five-phase, high-frequency voltage source inverter (VSI) are proposed and evaluated in this article. These techniques are based on choosing a set of vectors that limits the CMV amplitude. Operating the VSI under high-frequency pulsewidth modulations (PWM) generates a large number of changes in the CMV levels, which leads to common-mode currents (CMCs) and conducted electromagnetic interferences (EMIs). The proposed modulation techniques achieve the following: 1) High-efficiency converter operation and output voltage with low total harmonic distortion (THD); 2) an 80% reduction in CMV peak-to-peak amplitude; 3) a decrease in the number of the CMV transitions, thus reducing the CMCs; and 4) a decrease in the conducted EMI amplitude. The use of single-loop and double-loop $\Sigma$$\Delta$ modulators is analyzed by means of Matlab/Simulink and PLECS simulations. The implementation of the proposed modulation techniques has been experimentally evaluated using a five-phase VSI with silicon carbide semiconductors. In order to demonstrate the improved performance, the results obtained are compared with those of other PWM and space vector modulation techniques that also mitigate the CMV amplitude by 80% but lack the other improvements.
Multiphase Synchronous Machines vary in rotor construction and winding distribution leading to non-sinusoidal inductances along the rotor periphery. Moreover, saturation and cross-saturation effects make the precise modeling a complex task. This paper proposes a general model of multi-phase magnet-excited synchronous machines considering multi-dimensional space modeling and revealing cross-harmonic saturation. The models can predict multiphase motor behavior in any transient state, including startup. They are based on flux maps obtained from static 2D Finite-Element (FE) analysis. FE validations have been performed to confirm authenticity of the dynamic models of multiphase PMaSynRMs. Very close to FE precision is guaranteed while computation time is incomparably lower.
This paper presents a comprehensive analysis of SVPWM for a five-phase VSI based on SiC devices applied to motor drives. The modulation techniques analyzed use medium and large vectors to reach the reference vector. The 2L SVPWM uses two large space vectors, and the generated output signal contain low frequency harmonics. 2L+2M SVPWM uses two large and two medium space vectors. This technique provides good power loss distribution. 4L SVPWM works with the activation of four large space vectors. This modulation is able to generate low common-mode voltage. The performance and main features are analyzed using Matlab/Simulink and PLECS blockset software. Power losses, total harmonic distortion and common-mode voltage are compared and evaluated.