Connecting legs in parallel in a voltage source inverter is a way to increase the output current and, thus, its rated power. The connection can be made using either coupled or uncoupled inductors, and achieving an even contribution to the output current from all the legs is a crucial issue. Circulating currents produce additional losses and stress to the power devices of the converter. Therefore, they should be controlled and minimized. An efficient technique to attain such balance when coupled inductors are used is presented in this paper. The proposed technique can also be used when the inductors are uncoupled, since it is a particular case where the coupling coefficients are zero. This technique does not include proportional-integral controllers and does not require any parameter tuning either. The exact control action needed to reach current balance is straightforwardly calculated and applied. Experimental results are shown in this paper to verify the efficiency of the proposed balancing method.
28 April 2015 in IEEE Transactions on Power Electronics
This letter proposes a new implementation of phase-disposition pulse-width modulation (PD-PWM) for multilevel flying capacitor (FC) converters using a single triangular carrier. The proposed implementation is much simpler than conventional PD-PWM techniques based on multiple trapezoidal-shaped carriers, generates the same results as far as natural capacitor voltage balance is concerned and offers better quality line-to-line voltages when compared to phase-shifted PWM. The proposed algorithm is based on reshaping the reference signal to fit within the range of a single carrier and assigning each crossing of the reference signal with the carrier to a particular pair of switches at any time. The proposed algorithm is suitable for digital implementation taking maximum benefit from the PWM units available in the processor. Simulation and experimental results are presented from the five-level FC converter to verify the proposed PD-PWM implementation.
18 July 2014 in IEEE Transactions on Power Electronics
This letter presents a novel implementation of pulse width modulation that improves the quality of the line-to-line output voltages in interleaved multiphase voltage-source inverters (VSIs). In multiphase VSIs with n interleaved parallel-connected legs, the best single-phase output voltage is achieved when the carriers are evenly phase shifted. However, switching among nonadjacent levels can be observed at regular intervals in the line-to-line voltages, causing bad harmonic performance. With the proposed method, switching in the line-to-line voltages happens exclusively between adjacent levels. The modulator utilizes two sets of n evenly phase-shifted carriers that are dynamically allocated. Because of its generality, the proposed implementation is valid for any number of phases and any number of legs in parallel. A MATLAB/Simulink model has been set up for simulation purposes. Selected experimental results obtained from a three-phase VSI made up with two and three legs in parallel per phase are reported, confirming the enhancement attained with the proposed implementation.
26 January 2016 in IEEE Transactions on Power Electronics
This letter proposes a phase-shifted pulse-width modulation (PS-PWM) technique for the flying capacitor (FC) multilevel converter that improves the quality of the line-to-line voltages. In traditional PS-PWM, the line-to-line voltages include intervals that switch between nonadjacent voltage levels, which deteriorates the harmonic performance. The proposed PS-PWM constantly achieves line-to-line voltages with switching transitions between two adjacent levels. The proposed modulation technique is implemented using two sets of n evenly phase-shifted carriers that are alternatively applied depending on the instantaneous value of the reference signal of each phase-leg. Furthermore, it can be implemented in FC multilevel converters with any number of levels while maintaining natural capacitor voltage balance. Experimental results from a four-level FC converter prototype are presented.
26 June 2018 in IEEE Transactions on Industrial Electronics
Discontinuous modulation applied to modular multilevel converters is an effective method for reducing the capacitor voltage ripples. In this paper, the discontinuous modulation is adapted and used in a motor drive application. For proper operation of the converter, a new energy controller is presented, which is suitable for operation with nonsinusoidal reference signals. Experimental results comparing the discontinuous modulation with other techniques operating at low motor speeds are shown. The results demonstrate the effectiveness of the discontinuous modulation on reducing capacitor voltage ripples and power losses.
26 January 2016 in IEEE Transactions on Industrial Electronics
Interleaving of voltage-source converter (VSC) legs enables higher output currents per phase, effectively increasing the power rating without increasing semiconductor ratings. However, the interleaved operation results in circulating currents between each phase converter legs as well as a zero-sequence circulating current (ZSCC), which become quite prominent when the converters operate with low switching frequencies. This paper demonstrates the interleaved operation of three-level converters under selective harmonic elimination pulsewidth modulation (SHE-PWM). A controller for the circulating current within the legs of each phase is also proposed. The controller is used in combination with optimally selected SHE-PWM patterns to generate the maximum number of voltage levels and minimize the peak value of the circulating current. Simulation and experimental results show the interleaved operation and the effect of SHE-PWM pattern selection in the overall system.