Mahnaz Shamshirsaz

Prof. Mahnaz Shamshirsaz


Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 November 2020 in Polymers
Verified
Journal Article
Open access
PDF file
Fatemeh MokhtariFatemeh Mokhtari
Fatemeh Mokhtari
MSMahnaz Shamshirsaz
Mahnaz Shamshirsaz
MLMasoud Latifi
Masoud Latifi
Javad ForoughiJavad Foroughi
Javad Foroughi
The demands for wearable technologies continue to grow and novel approaches for powering these devices are being enabled by the advent of new energy materials and novel manufacturing strategies. In addition, decreasing the energy consumption of portable electronic devices has created a huge demand for the development of cost-effective and environment friendly alternate energy sources. Energy harvesting materials including piezoelectric polymer with its special properties make this demand possible. Herein, we develop a flexible and lightweight nanogenerator package based on polyvinyledene fluoride (PVDF)/LiCl electrospun nanofibers. The piezoelectric performance of the developed nanogenator is investigated to evaluate effect of the thickness of the as-spun mat on the output voltage using a vibration and impact test. It is found that the output voltage increases from 1.3 V to 5 V by adding LiCl as additive into the spinning solution compared with pure PVDF. The prepared PVDF/LiCl nanogenerator is able to generate voltage and current output of 3 V and 0.5 μA with a power density output of 0.3 μW cm−2 at the frequency of 200 Hz. It is found also that the developed nanogenerator can be utilized as a sensor to measure temperature changes from 30 °C to 90 °C under static pressure. The developed electrospun temperature sensor showed sensitivity of 0.16%/°C under 100 Pa pressure and 0.06%/°C under 220 Pa pressure. The obtained results suggested the developed energy harvesting textiles have promising applications for various wearable self-powered electrical devices and systems.

13 September 2011 in Journal of Intelligent Material Systems and Structures
Verified
Journal Article
Closed access
NSN. Sepehry
N. Sepehry
MSMahnaz Shamshirsaz
Mahnaz Shamshirsaz
FAF. Abdollahi
F. Abdollahi
In this article, a new method for temperature compensation on the basis of artificial neural networks (ANNs) in impedance-based structural health monitoring (ISHM) has been introduced. ISHM using piezoelectric wafer active sensors (PWAS) has been extensively developed to provide detection of fault in structure. The principle of this method is based on the electromechanical coupling effect of PWAS materials. Any change in structure leads to changes in mechanical impedance of structure. The electrical impedance of PWAS can sense this change by the electromechanical coupling effect of PWAS. Therefore, the difference in this electrical impedance for undamaged and damaged structures can be considered as a damage index to detect the damage in structure. Since physical and mechanical properties of structure also PWAS materials are temperature dependent, so this electrical impedance of PWAS will be affected by temperature changes. Consequently, the variation in environmental or service temperatures can be detected erroneously as damage in ISHM method. In this article, a new method using ANN based on radial basis function (RBF) has been proposed and developed to compensate the temperature effect on the damage index. A steel plate and gas pipe with bolted joints are considered as two case studies for the performance evaluation of the proposed fault detection methodology. Results confirm that the proposed method using the ANN can be effectively utilized to compensate temperature variation for damage detection in different structures.

21 December 2010 in Structural Health Monitoring
Verified
Journal Article
Closed access
PDF file
NSNaserodin Sepehry
Naserodin Sepehry
MSMahnaz Shamshirsaz
Mahnaz Shamshirsaz
ABAli Bastani
Ali Bastani
In the recent years, the piezoelectric wafer active sensors (PWASs) are increasing as a measurement tool in structural health monitoring techniques. In impedance-based structural health monitoring (ISHM) method, the electrical impedance of a PWAS bonded to the structure is measured and served as a defect detection index of the structure. The principle of this method is based on the electromechanical coupling effect of PWAS materials. As any change in the structure will lead to a change in mechanical impedance of structure, the electrical impedance of PWAS could sense this change by the electromechanical coupling effect of PWAS. Since the physical and mechanical properties of PWAS materials are temperature-dependent, so the electrical impedance of PWAS will change with varying temperature. Consequently, the changes in environmental or service temperatures could be detected in ISHM method as a defect. In this article, in order to consider the temperature dependency of PWAS material properties, a temperature-dependent model is developed for a PWAS bonded to an Euler Bernoulli cantilever beam. An aluminum (alloy 2024) beam was examined experimentally by ISHM method in order to validate the proposed model. The comparison of theoretical and experimental results demonstrates a good improvement in ISHM modeling where temperature variation is present.


14 December 2011 in Structural Health Monitoring
Verified
Journal Article
Closed access
ABAli Bastani
Ali Bastani
HAHamidreza Amindavar
Hamidreza Amindavar
MSMahnaz Shamshirsaz
Mahnaz Shamshirsaz
NSNaserodin Sepehry
Naserodin Sepehry
Impedance-based structural health monitoring (ISHM) using piezoelectric materials has been extensively developed to provide a structure health indicator. In practice, due to the environmental disturbances, the received signal in different surrounding conditions may be different from intact structure received signal. In the past, any difference was assumed being caused by damage even changes such as temperature effects on the received signal. In ISHM, the received signal is different from the intact structure received signal; however, there is not necessarily damage in the system. So, the validity of ISHM depends on the identification of environmental disturbances in order to extract the real results from disturbed results. In this article, a new method using sensor array and statistical metric analysis has been proposed to identify signal changes derived from damage and/or environmental change. Using this method, it is expected that the environmental variations affect similarly on output signals of different row sensors, whereas changes caused by damage will not be similar for all row and column sensors. This expectation is a general fact because there would be no sensible difference in the environmental variations from one side to other sides of the structure. To identify environmental disturbance from damage detection, an analysis is developed using statistical metrics. Experimental results show that this method is reliable to identify damage.

23 February 2008 in Microsystem Technologies
Verified
Journal Article
Closed access
PDF file
MSMahnaz Shamshirsaz
Mahnaz Shamshirsaz
MAM. B. Asgari
M. B. Asgari