Bowen Xu

Dr. Bowen Xu

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2022 in Journal of Materials in Civil Engineering
Verified
Journal Article
Closed access
PDF file
DBD. V. Bompa
D. V. Bompa
BXBowen Xu
Bowen Xu
Ofelia Cornelia CORBUOfelia Cornelia CORBU
Ofelia Cornelia CORBU
This paper describes an experimental investigation into the properties of ambient cured one-part alkali-activated materials (AAMs). Mixes incorporating waste glass (WG), ground granulated blast-furnace slag (GGBS), fly ash (FA), and sodium metasilicate pentahydrate were assessed in terms of workability, water absorption, physical and mechanical properties, and environmental impact. Microstructure investigations on selected mixes were also carried out. The GGBS-only mixes had low workability and high early strength that declined over time, whereas FA-only mixes had virtually no strength. Equal proportions of WG and GGBS provided similar fresh properties to those of GGBS mixes yet comparatively higher strengths and a positive strength time gradient. Mixes incorporating 50% GGBS, 25% FA, and 25% WG had the best balance between mechanical properties and workability, with compressive strengths above 40 MPa suitable for structural applications. An increase in activator content from 14% to 21% enhanced the strengths by 39.1%–54.6%. The flexural strengths were largely proportional to the compressive strengths, the water absorption properties were like those of cement mortars, and dry densities depended on the proportions of the constituent binders. Finally, the AAM mixes had between 53% and 72% less embodied carbon compared with a corresponding cement mortar.

1 January 2018 in Construction and Building Materials
Verified
Journal Article
Open access
BXBowen Xu
Bowen Xu
DBDan Bompa
Dan Bompa
AEAhmed Elghazouli
Ahmed Elghazouli
ARA.M. Ruiz-Teran
A.M. Ruiz-Teran
PSP.J. Stafford
P.J. Stafford
This paper deals with the experimental behaviour of rubberised concrete members subjected to asymmetric four-point shear loading. A detailed account of tests on 15 prismatic members using conventional concrete as well as rubberised concrete, with relatively high replacement ratios of both fine and coarse mineral aggregates with rubber particles, is given. The results enable direct assessment of strength and complete deformation characteristics including the post-peak response for ultimate behaviour governed both by shear and mixed-mode tensile-shear. After describing the material properties, mix designs and member details, the main observations from detailed measurements of the crack kinematics through a digital image correlation monitoring system, with focus on members developing shear-governed response, are reported. Complementary numerical studies are undertaken using nonlinear finite element procedures which are validated against tests developing shear-governed failures. In order to provide further insight into the key response characteristics, particularly those related to ultimate strength, a number of numerical sensitivity studies employing various constitutive parameters are also carried out. Moreover, comparative assessments in terms of shear resistance, toughness and force transfer across the cracked interfaces are performed and discussed. The detailed test measurements, coupled with the results obtained from the numerical simulations, permit the definition of expressions for representing the shear resistance as a function of the rubber content and concrete compressive strength

20 November 2020 in IEEE Access
Verified
Journal Article
Open access
CCChen Cao
Chen Cao
BXBowen Xu
Bowen Xu
XLXuebin Li
Xuebin Li
In order to monitor loosened state and deformational fault for transformer winding, the monitoring method based on vibration and reactance information is proposed in this paper. Theoretical models of winding deformational state with vibration and reactance information are established and calculated. Multi-information monitoring model is established, which include vibration and reactance information monitoring method. Multi-information integrated monitoring strategy is proposed. The CEEMD-energy entropy transformation method is proposed to extract vibration feature information, and reactance feature information is extracted by reactance identification method. Aiming at a 500kVA, 35kV transformer prototype, experiment of short circuit current impact is carried on, three types of deformational windings including radial extend in middle position, axial stretching loosened and coil folding in end position are developed. Monitoring experiment on loosened state winding after multi-short circuit current impacts and three types of deformational fault windings are carried on. The monitoring results are consistent with the actual deformational state of transformer windings. Loosened state and deformational fault of windings can be monitored by proposed monitoring method based on vibration and reactance information effectively, which provide basis for multi-information monitoring.

2 November 2021 in Infrastructures
Verified
Journal Article
Open access
PDF file
Natividad Leonor Garcia-TroncosoNatividad Leonor Garcia-Troncoso
Natividad Leonor Garcia-Troncoso
BXBowen Xu
Bowen Xu
WPWilhenn Probst-Pesantez
Wilhenn Probst-Pesantez
Recycling of construction and demolition waste is a central point of discussion throughout the world. The application of recycled concrete as partial replacement of mineral aggregates in concrete mixes is one of the alternatives in the reduction of pollution and savings in carbon emissions. The combined influence of the recycled crushed concrete, lime, and natural pozzolana on the mechanical and sustainable properties of concrete materials is firstly proposed in this study. In this research, unconventional construction materials are employed to produce concrete: the recycled crushed concrete is used as coarse aggregate, while lime and natural pozzolana are used as a partial replacement for cement. Substitutions of 10%, 20%, 50% of gravel are made with recycled aggregates, and 2%, 5%, 10% of cement with lime and natural pozzolan. Tests on the fresh and hardened properties, destructive (compressive strength) and non-destructive tests (sclerometer rebound and ultrasound) of mixtures are carried out. It is shown that the use of recycled materials can provide an increase in compressive strength of up to 34% with respect to conventional concrete. Life cycle cost and sustainability assessments indicate that concrete materials incorporating recycled aggregate possess good economic and environmental impacts.

28 December 2024 in Sustainability
Verified
Journal Article
Open access
PDF file
NANouf Almonayea
Nouf Almonayea
Natividad Leonor Garcia-TroncosoNatividad Leonor Garcia-Troncoso
Natividad Leonor Garcia-Troncoso
BXBowen Xu
Bowen Xu
DBDan Bompa
Dan Bompa
This study evaluates the environmental impact of alkali-activated concrete materials (AACMs) as alternatives to conventional concrete. The influence of binder and activator content and type, along with other mix parameters, is analysed using a probabilistic embodied carbon assessment on a large dataset that includes 580 mixes. Using a cradle-to-gate approach with region-specific life-cycle inventory data, emissions are analysed against binder intensity, activator-to-binder and water-to-binder ratios, and fresh/mechanical properties. A multicriteria assessment quantifies the best-performing mix in terms of embodied carbon, compressive strength, and slump. AACM environmental impact is compared to conventional concrete through existing classification schemes and literature. AACM emissions vary between 41 and 261 kgCO2eq/m3, with activators contributing the most (3–198 kgCO2eq/m3). Uncertainty in transport-related emissions could shift these values by ±38%. AACMs can achieve up to four-fold less emissions for high-strength materials compared to conventional concrete, although this benefit decreases with lower mechanical properties. AACM environmental sustainability depends on activator characteristics, curing, mix design, and transportation.

2 September 2021 in Infrastructures
Verified
Journal Article
Open access
PDF file
BXBowen Xu
Bowen Xu
HLHui Li
Hui Li
DBDan Bompa
Dan Bompa
AEAhmed Elghazouli
Ahmed Elghazouli
JCJiangbo Chen
Jiangbo Chen
This paper investigates the electrical, thermal and mechanical properties as well as the environmental performance of polymer cementitious composites (PCCs) as sustainable coating materials for underground power cables and as high-voltage insulators. Particular focus is placed on the optimised mix design and the effect of the manufacturing method on the performance of PCCs, incorporating liquid styrene and acrylic (SA) monomers, wollastonite and muscovite. Microstructural investigations, together with results from strength tests, indicate that the manufacturing method is a key performance parameter. Experimental results show that PCC mixes containing 25% SA emulsion, 12.5% wollastonite and no muscovite provide the most favourable dielectric properties from the mixes investigated. The PCC material has a dielectric strength up to 16.5 kV/mm and a dielectric loss factor lower than 0.12. Additional experiments also show that PCC has good thermal stability and thermal conductivity. The mechanical strength tests indicate that PCC specimens possess reliable strengths which are applicable in structural design. Environmental assessments also show that PCCs possess significantly lower embodied energy and embodied carbon than conventional plastic insulating materials.