Patrik Šarga

Dr. Patrik Šarga

Technical University of Košice
orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2012 in Procedia Engineering
Verified
Journal Article
Open access
DHDarina Hroncová
Darina Hroncová
MBMichal Binda
Michal Binda
PŠPatrik Šarga
Patrik Šarga
FKFrantišek Kičák
František Kičák

1 January 2012 in Procedia Engineering
Verified
Journal Article
Open access
PŠPatrik Šarga
Patrik Šarga
DHDarina Hroncová
Darina Hroncová
MČMiloslav Čurilla
Miloslav Čurilla
AGAlexander Gmiterko
Alexander Gmiterko
The work shows the use of Bond Graph formalism for modeling dynamic systems. As an example a electrical model is solved by this approach at the level of its physical behavior. In contrast with the classical method, where the equations for individual components are created first and then the simulation scheme is derived on their basis, the described method uses the reverse procedure. In this paper the method of generation of system equations is discussed. From a bond graph diagram of the system, using a step-by-step procedure, system equations may be generated. As a starting point a model of a simple electrical RLC circuit consisting of a resistor, an inductor, and a capacitor is taken. The differential equations describing the dynamics of the system are obtained in terms of the states of the system

1 September 2016 in International Journal of Advanced Robotic Systems
Verified
Journal Article
Open access
TLTomáš Lipták
Tomáš Lipták
Ivan VirgalaIvan Virgala
Ivan Virgala
PFPeter Frankovský
Peter Frankovský
PŠPatrik Šarga
Patrik Šarga
AGAlexander Gmiterko
Alexander Gmiterko
LBLenka Baločková
Lenka Baločková
The article deals with the issue of use of geometric mechanics tools in modelling nonholonomic systems. The introductory part of the article contains fiber bundle theory that we use at creating mathematical model of nonholonomic locomotion system with undulatory movement. Further the determination of general mathematical model for n-link snake-like robot is presented, where we used nonholonomic constraints. The relation between changes of shape and position variables was expressed using the local connection that was used to analyze and control system movement by vector fields. The effect of links number of snake-like robot on its mathematical model was investigated. The last part of this article consists of detailed description of modeling reconstruction equation for four- and five-link snake-like robot.

17 November 2020 in Materials
Verified
Journal Article
Open access
PDF file
MPMiroslav Pástor
Miroslav Pástor
JBJozef Bocko
Jozef Bocko
PLPavol Lengvarský
Pavol Lengvarský
PSPeter Sivák
Peter Sivák
PŠPatrik Šarga
Patrik Šarga
Technological units of water reservoirs and power plants include sluice gates which are designed to completely seal the inflow or outflow of water in supply or discharge channels. This article describes the issue of technical assessment of a sluice gate made in the 1950s. Such structures are characterised by states of significant corrosive wear, permanent deformations of contact and sealing surfaces as well as increased levels of residual stresses. In such cases, it is difficult to determine service life using only numerical modelling methods, mainly due to problematic definition of material properties and boundary conditions. Therefore, for safety assessment, it is necessary to verify these facts experimentally. This article presents the procedure for assessing safe operation of the sluice gate on which places with permanent deformation and a broken part of the guide wheel flange were identified. By means of numerical modelling, we identified critical stress values at the locations of reinforcing elements, which were modified, and the stress values were reduced by about 15%. The results of numerical modelling were verified at select locations by experimental measurements during operation using strain gauges. The maximum values of operational normal stresses in the assessed places reached about 27 MPa. Based on the comparison of obtained results and taking into account values of residual stresses reaching up to 190 MPa made by shielded metal arc welding, it can be stated that, for safe operation of the sluice gate, it is necessary to follow the proposed procedure during its lowering and to modify the reinforcing elements structurally.

1 December 2013 in Applied Mechanics and Materials
Verified
Journal Article
Closed access
PDF file
FMFrantišek Menda
František Menda
FTFrantišek Trebuňa
František Trebuňa
PŠPatrik Šarga
Patrik Šarga
There are several measuring techniques for determining residual stress which can be divided according to the created damage in to the construction in non-destructive, semi-destructive and destructive ones. One of the most common is semi-destructive hole-drilling method. This paper deals about Ring-Core method which is based on the similar principles. Today, there is no standard for the Ring-Core method, thus it is important to consider various influential factors. One of them are the dimensions of specimen. Calibration coefficients are determined by finite element (FE) analysis using the commercial software Solidworks. These coefficients are used for residual stress evaluation by incremental method used in Ring-Core method. The influence of different specimen dimensions on the accuracy of the evaluated residual stresses is considered.

31 January 2011 in Engineering Failure Analysis
Verified
Journal Article
Closed access
FTFrantišek Trebuňa
František Trebuňa
FŠFrantišek Šimčák
František Šimčák
JBJozef Bocko
Jozef Bocko
PTPeter Trenbuna
Peter Trenbuna
MPMiroslav Pástor
Miroslav Pástor
PŠPatrik Šarga
Patrik Šarga