Peirong Zhang

Prof. Dr. Peirong Zhang

School of Mechanical and Automotive Engineering, Qilu University of Technology (Shandong Academy of Sciences), Jinan 250353, China
orcid

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2018 in Biomedicine & Pharmacotherapy
Verified
Journal Article
Closed access
YLYuqiang Liang
Yuqiang Liang
Peirong ZhangPeirong Zhang
Peirong Zhang
SLShaohong Li
Shaohong Li
HLHeng Li
Heng Li
SSShaofang Song
Shaofang Song
BLBaolan Lu
Baolan Lu

20 November 2018 in Materials and Corrosion
Verified
Journal Article
Closed access
PDF file
Peirong ZhangPeirong Zhang
Peirong Zhang
Zhanqiang LiuZhanqiang Liu
Zhanqiang Liu
GSGuosheng Su
Guosheng Su
JDJin Du
Jin Du
JZJingjie Zhang
Jingjie Zhang

8 April 2020 in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
Verified
Journal Article
Closed access
PDF file
Peirong ZhangPeirong Zhang
Peirong Zhang
Zhanqiang LiuZhanqiang Liu
Zhanqiang Liu
Jin DuJin Du
Jin Du
Guosheng SuGuosheng Su
Guosheng Su
JZJingjie Zhang
Jingjie Zhang
YSYujing Sun
Yujing Sun
The machinability of the Al–Si alloys becomes worse with the Si content increasing. This article explored the influence of Si content on the machinability including cutting forces and chip breakability in machining the Al–Si alloys. The change in machinability of the Al–Si alloys with different Si content attributes to the evolution of microstructure. The cutting forces when cutting hypoeutectic Al–Si alloys are higher than the hypereutectic alloys because only Mg2Si ( β-phase) precipitations are formed in the former one versus cooperative precipitation of Al2Cu ( θ-phase) and Mg2Si in the latter. With regard to hypereutectic Al–Si alloys, cutting force components decrease with the increase in Si content due to the formation of brittle primary Si, which induces the initiation of cracks in material removal process. Moreover, the cutting stability of Al–Si alloys is improved with Si contents in the range of 12–18 wt%, while deteriorates for the Si content of 25 wt%. Besides, the chip breakability is improved due to the increase in eutectic silicon in hypoeutectic and eutectic ranges and because of the formation of block-shaped primary Si for hypereutectic alloys. The optimization of Si content is 12–18 wt% with cutting speed not less than 150 m/min.

26 June 2020 in Archives of Civil and Mechanical Engineering
Verified
Journal Article
Open access
PDF file
Peirong ZhangPeirong Zhang
Peirong Zhang
JDJin Du
Jin Du
HZHui Zhang
Hui Zhang
GSGuosheng Su
Guosheng Su
XSXuehui Shen
Xuehui Shen
ZLZhanqiang Liu
Zhanqiang Liu
The hydraulic support column of comprehensive mining equipment is the most important part, subjecting to corrosion, wear and collision. The scrapped columns are restored by laser cladding to replace plating process for enhancing service life. All that is required after laser cladding is subtractive machining to improve the surface quality of the laser cladded coatings. This work focused on the remanufacturing machining strategy for re-contouring the laser cladding restored columns. First, surface roughness model of the laser cladded coatings by turn-burnishing was presented based on the surface generation mechanism. Then the effect of turning-induced roughness level on the surface roughness improvements by subsequent burnishing is addressed. Results indicated that the reduction of surface roughness by burnishing showed positive correlation with the feed in initial turning with conventional inserts, while was negatively correlated with the feed in initial turning with wiper inserts. In addition, the initial turning-induced surface roughness level generated great influence on the residual stress improvement in subsequent burnishing. Based on the findings, proper remanufacturing machining strategies for re-contouring the laser cladding-restored hydraulic support columns were presented.

26 October 2016 in Materials
Verified
Journal Article
Open access
PDF file
SLShuyue Liu
Shuyue Liu
Zhanqiang LiuZhanqiang Liu
Zhanqiang Liu
Peirong ZhangPeirong Zhang
Peirong Zhang
Titanium and its alloys have been widely used as implant materials due to their excellent mechanical property and biocompatibility. In the present study, the effect of glucose concentration on corrosion behavior of pure titanium TA2 in Hanks’ simulated body fluid is investigated by the electrochemical impedance spectrum (EIS) and potentiodynamic polarization methods. The range of glucose concentrations investigated in this research includes 5 mmol/L (limosis for healthy people), 7 mmol/L (after diet for healthy people), 10 mmol/L (limosis for hyperglycemia patient), and 12 mmol/L (after diet for hyperglycemia patient), as well as, 15 mmol/L and 20 mmol/L, which represent different body fluid environments. The results indicate that the pure titanium TA2 demonstrates the best corrosion resistance when the glucose concentration is less than 10 mmol/L, which shows that the pure titanium TA2 as implant material can play an effective role in the body fluids with normal and slight high glucose concentrations. Comparatively, the corrosion for the pure titanium implant is more probable when the glucose concentration is over 10 mmol/L due to the premature penetration through passive film on the material surface. Corrosion defects of pitting and crevice exist on the corroded surface, and the depth of corrosion is limited to three microns with a low corrosion rate. The oxidation film on the surface of pure titanium TA2 has a protective effect on the corrosion behavior of the implant inner material. The corrosion behavior of pure titanium TA2 will happen easily once the passive film has been penetrated through. The corrosion rate for TA2 implant will accelerate quickly and a pure titanium implant cannot be used.

3 April 2024 in Metals
Verified
Journal Article
Open access
PDF file
YYYandong Yin
Yandong Yin
Jin DuJin Du
Jin Du
YSYujing Sun
Yujing Sun
YXYAN XIA
YAN XIA
Peirong ZhangPeirong Zhang
Peirong Zhang
Guosheng SuGuosheng Su
Guosheng Su
A fine-grained WC-15wt%Al0.5CoCrFeNi cemented carbide was prepared through a vacuum and gas pressure sintering. For achieving high surface integrity, diamond wheel grinding serves as the primary molding process for the machining of WC cemented carbide. To reveal the influence of grinding on the surface integrity of fine-grained WC-HEA cemented carbide, studies were conducted on grinding force, surface microstructure, surface roughness, residual stress, microhardness, and bending strength. The morphological analysis of the ground surface indicated a transition in the material removal mechanism of WC-HEA cemented carbide from ductile removal to brittle removal, with brittle removal becoming predominant as the depth of grinding increases. With the increasing depth of grinding, the grinding force increases, and the grinding force increases while the surface roughness decreases. Correspondingly, there is an improvement in both hardness and bending strength. Additionally, grinding induces high residual compressive stress on the surface, with a maximum compressive stress of 1795 MPa. The bending strength of the material is found to be dependent on the residual stress.