Micro-hole arrays have found wide applications in aerospace, precision instruments, and biomedicine. Among various methods of their production, including mechanical, laser, and electrical discharge, electrochemical machining (ECM) is considered the most lucrative due to its wide processing range, high surface quality, and excellent productivity. In particular, ultrasound-assisted through-mask ECM exhibits an enhanced machining precision due to ultrasonic cavitation, which promotes the removal of the electrolytic products and bubbles. In this study, the equation of cavitation bubble oscillation was derived and numerically solved to study the influence of six different parameters on the ultrasonic cavitation and electrolysis process, and their optimal values were determined. The feasibility of the proposed ultrasound-assisted through-mask ECM technology with the optimized parameters was experimentally corroborated by the fabrication of a high-quality hole array in an oxide dispersion strengthened (ODS) MA956 superalloy.
31 March 2023 in The International Journal of Advanced Manufacturing Technology
Molybdenum is an important material in modern industry, widely used in extreme environments such as rocket engine nozzles and microelectrodes due to its high melting point, excellent mechanical properties, and thermal conductivity. However, as a difficult-to-machine metal, traditional machining methods struggle to achieve the desired microstructures in molybdenum. Electrochemical machining (ECM) offers unique advantages in manufacturing fine structures from hard-to-machine metals. Studies have shown that molybdenum exhibits a fast corrosion rate in alkaline or acidic solutions, posing significant environmental pressure. Therefore, this study investigates the electrochemical machining of molybdenum in neutral salt solutions to achieve high-precision microstructure fabrication. First, the polarization curves and electrochemical impedance spectroscopy (EIS) of molybdenum in NaNO3 solutions of varying concentrations were measured to determine its electrochemical reaction characteristics. The results demonstrate that molybdenum exhibits good electrochemical reactivity in NaNO3 solutions, leading to favorable surface erosion morphology. Subsequently, a mask electrochemical machining technique was employed to fabricate arrayed microstructures on the molybdenum surface. To minimize interference between factors, an orthogonal experiment was used to optimize the parameter combination, determining the optimal machining process parameters. Under these optimal conditions, an array of micro-groove structures was successfully fabricated with an average groove width of 110 μm, a depth-to-width ratio of 0.21, an aspect ratio of 9000, and a groove width error of less than 5 μm.
To solve the problem of the nonuniform distribution of temperature and electrolytic products in the electrolyte flow field during through-mask electrochemical micromachining, the use of a rotating cathode with surface structures is proposed. The rotation of the cathode increases the efficiency of heat and mass transfer by the electrolyte flow. Simulations are performed to analyze the influence of the type of surface structure, the number of surface structures, and the rotational speed of the cathode on the electrolyte flow field. The results show that the use of a rotating cathode with surface structures significantly improves the mass transfer efficiency of the electrolyte flow field in comparison with a conventional cathode structure, and, in particular, a grooved rotating cathode can increase the outlet flow velocity by about 23%. An experimental demonstration of micropit array processing shows that the use of a grooved rotating cathode increases the mass transfer efficiency by 34% and the processing efficiency by nearly 40% compared with a smooth-surfaced rotating cathode. The grooved rotating cathode also gives the highest machining accuracy. Using this cathode, a uniform micropit array with an average micropit diameter of 201.83 μm, a diameter standard deviation of 3.49 μm, and a depth standard deviation of 0.87 μm is processed.
The uniformity of microstructural formation remains a critical challenge in mask-assisted electrochemical micro-etching (M-ECME), primarily governed by electric field and flow field distribution. Implementation of a pulsating-cycle cathode in M-ECME enabled self-sustained pulsed machining. Multiphysics simulations verified control over current and flow fields, while theoretical analysis established 0.253 mm as the optimal activation gap. The cyclically moving cathode acts like a piston to refresh the electrolyte in the machining zone, and cathode velocity should be limited to below 0.16 m/s to prevent cavitation in the flow field. Subsequent machining experiments strongly validated these theoretical findings. Optimized parameters (15 V, 0.14 m/s) produce highly consistent microstructures (245.28 ± 5.50 μm diameter, 50.34 ± 5.49 μm depth) with significantly improved dimensional control.
The manufacturing of surface microstructure is an important means for the modification of surface characteristics of parts. Through-mask electrochemical manufacturing is also an efficient way to fabricate surface microstructures. Nevertheless, in cases where the through-mask electrochemical manufacturing is used for the fabrication of microstructures, many experiments are required to control the cross-section morphology of the microstructures. Furthermore, there is a lack of quantitative analysis of the impact of key variables on the process. In this paper, using numerical simulations based on the geometric structure of mask feature, we analyze the effects of the aspect ratio of mask feature and the gap between cathode to mask on electrochemical micromachining. We further investigate the influence laws of the mask feature’s geometric structure on the anode current density distribution and forming process. A critical value of "0.8" is also determined for aspect ratio of mask feature which is closely related to the anode current density distribution and forming process. The through-mask electrochemical micromachining experiments confirm the effect laws of the geometric structure of the mask feature. And the critical value (0.8) of aspect ratio can be used as the basis for selecting mask feature.