Benedikt Adelmann

Benedikt Adelmann


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 December 2022 in Metals
Verified
Journal Article
Open access
PDF file
BABenedikt Adelmann
Benedikt Adelmann
Ralf HellmannRalf Hellmann
Ralf Hellmann
We compare different lattice structures with various elementary cell sizes built by laser powder bed fusion with and without hot isostatic pressing as post treatment. Cylindrical lattice structures are mechanically tested upon static and dynamic load in order to achieve high elasticity, high fracture strength and a high number of cycles to failure with respect to applications as medical implants. Evaluating the Young’s modulus, a high stiffness for the body diagonal structure and a low fracture stress for the G-structure are measured. Hot isostatic pressing results in a higher Young’s modulus and is ambiguous in terms of fractural stress. While samples without hot isostatic pressing reveal a shear fracture, the hot isostatic pressed samples have a high ductile area where the lattice layers are wrapped and pressed into the underlying layers without a fracture. Under dynamic load, the samples without hot isostatic pressing mostly are unable withstand 106 cycles at typical loads of the human body. Hot isostatic pressing has no significant influence on the strength at high loads and low cycle numbers, but at low loads all samples survived 106 cycles. As a consequence, dode-thick and rhombic dodecahedrons with 2 mm and 1.5 mm lattice size after hot isostatic pressing are recommended for medical implants because of the high elasticity, high fracture stress and high resistance against dynamic loads, which fulfill implant requirements.

30 August 2021 in Sensors
Verified
Journal Article
Open access
PDF file
BABenedikt Adelmann
Benedikt Adelmann
Ralf HellmannRalf Hellmann
Ralf Hellmann
In this contribution, we compare basic neural networks with convolutional neural networks for cut failure classification during fiber laser cutting. The experiments are performed by cutting thin electrical sheets with a 500 W single-mode fiber laser while taking coaxial camera images for the classification. The quality is grouped in the categories good cut, cuts with burr formation and cut interruptions. Indeed, our results reveal that both cut failures can be detected with one system. Independent of the neural network design and size, a minimum classification accuracy of 92.8% is achieved, which could be increased with more complex networks to 95.8%. Thus, convolutional neural networks reveal a slight performance advantage over basic neural networks, which yet is accompanied by a higher calculation time, which nevertheless is still below 2 ms. In a separated examination, cut interruptions can be detected with much higher accuracy as compared to burr formation. Overall, the results reveal the possibility to detect burr formations and cut interruptions during laser cutting simultaneously with high accuracy, as being desirable for industrial applications.

19 January 2021 in Sensors
Verified
Journal Article
Open access
PDF file
BABenedikt Adelmann
Benedikt Adelmann
MSMax Schleier
Max Schleier
Ralf HellmannRalf Hellmann
Ralf Hellmann
In this publication, we use a small convolutional neural network to detect cut interruptions during laser cutting from single images of a high-speed camera. A camera takes images without additional illumination at a resolution of 32 × 64 pixels from cutting steel sheets of varying thicknesses with different laser parameter combinations and classifies them into cuts and cut interruptions. After a short learning period of five epochs on a certain sheet thickness, the images are classified with a low error rate of 0.05%. The use of color images reveals slight advantages with lower error rates over greyscale images, since, during cut interruptions, the image color changes towards blue. A training set on all sheet thicknesses in one network results in tests error rates below 0.1%. This low error rate and the short calculation time of 120 µs on a standard CPU makes the system industrially applicable.

8 April 2022 in Sensors
Verified
Journal Article
Open access
PDF file
MSMax Schleier
Max Schleier
BABenedikt Adelmann
Benedikt Adelmann
CECemal Esen
Cemal Esen
Ralf HellmannRalf Hellmann
Ralf Hellmann
We present an in situ process monitoring approach for remote fiber laser cutting, which is based on evaluating images from a high-speed camera. A specifically designed image processing algorithm allows the distinction between complete and incomplete cuts by analyzing spectral and geometric information of the melt pool from the captured images of the high-speed camera. The camera-based monitoring system itself is fit to a conventional laser deflection unit for use with high-power fiber lasers, with the optical detection path being coaxially aligned to the incident laser. Without external illumination, the radiation of the melt from the process zone is recorded in the visible spectral range from the top view and spatially and temporally resolved. The melt pool size and emitted sparks are evaluated in dependence of machining parameters such as feed rate, cycles, and focus position during cutting electrical sheets.

27 November 2022 in Materials
Verified
Journal Article
Open access
PDF file
BABenedikt Adelmann
Benedikt Adelmann
TSTobias Schwiddessen
Tobias Schwiddessen
BGBabette Götzendorfer
Babette Götzendorfer
Ralf HellmannRalf Hellmann
Ralf Hellmann
We report on additively manufactured filter systems based on bionic manta ray structures and evaluate their filter performance. The filters are periodic lamella structures produced by selective laser sintering using PA12 polyamide powder. Two different lamella types are investigated, which are derived from two manta ray genera, namely, Mobula tarapacana and Manta birostris. The precipitator efficiency of sand particles in water is determined for both flow directions, which are referred to as the “wing” and “spoiler” arrangements. With a flat filter design, more than 90% of sand particles can be removed from the water. The variation of the lamella distance reveals that the filter effect is based on the different dynamic flow of particles and water rather than filtering by the hole size. The successful transformation of the primary flat filter design into a round filter structure is demonstrated with precipitator efficiencies above 95% and a ratio of filtered to unfiltered water of 1:1 being achieved, depending of the gap between the filter and the surrounding pipe. A shortening of the filter structure results in an unaltered precipitator efficiency but a lower ratio of filtered water. These results reveal the peculiar possibility to produce 3D round-shaped filters based on manta ray structures with additive manufacturing, achieving good precipitator efficiencies.

24 September 2022 in Materials
Verified
Journal Article
Open access
PDF file
BABenedikt Adelmann
Benedikt Adelmann
Ralf HellmannRalf Hellmann
Ralf Hellmann
We present a compressed air motor, completely built by laser powder bed fusion. To highlight the fully functional integration by additive manufacturing, the rotor, stator, bearings, turbine, gas inlet and outlet were all built in a single print job. The material used was Inconel 718, and the motor was 44 mm tall and 12 mm in diameter. With the rotation axis of the motor in print in the direction of the laser powder bed fusion process, no build supports are needed, and thus the rotor and stator are fully moveable against each other. Plain bearings were used to position the rotor inseparably inside the stator, with a bearing gap of 0.2 mm, resulting in stable rotation. The idle rotation speed of the motor was measured with a digital laser measuring device as a function of air pressure and inlet size. With linear behavior between the rotation speed and gas pressure of up to 5.5 bar, the motor can be easily controlled. With varying gas inlet sizes, the idle rotation speed of the compressed air motor is also varied. A maximum rotation speed of 90,000 rpm was achieved at 1.5 mm gas inlet size and 3 bar gas pressure.