Murugesan Mariappan

Dr. Murugesan Mariappan

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 September 2012 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
Takafumi FukushimaTakafumi Fukushima
Takafumi Fukushima
EIEiji Iwata
Eiji Iwata
YOYuki Ohara
Yuki Ohara
MMMurugesan Mariappan
Murugesan Mariappan
JBJichoel Bea
Jichoel Bea
MKMitsumasa Koyanagi
Mitsumasa Koyanagi
Self-assembly of multichips with metal microbump electrodes is demonstrated by using water surface tension to increase the stacking throughput/yield and chip alignment accuracy of conventional chip-to-wafer 3-D integration. Three-dimensional microbump interconnects are formed by self-assembly with thermal compression at 200°C. Chips with In-Au microbumps with pitches of 10 and 20 μm are tightly bonded to Si wafers after the flip-chip self-assembly process, resulting in high alignment accuracies of 0.8 and 0.2 μm in the x - and y-directions, respectively. Selective hydrophilization by 172-nm excimer lamp irradiation gives a high wettability contrast between hydrophilic chip bonding areas and hydrophobic surrounding areas on the wafers. This assists high-precision multichip self-assembly. A 2500-In-Au-microbump daisy chain is formed with a yield of 100% by flip-chip self-assembly, and it exhibits ohmic contact. The resistance is sufficiently low for 3-D large-scale integration application, being comparable to that obtained by conventional mechanical chip alignment.

10 October 2016 in Micromachines
Verified
Journal Article
Open access
PDF file
Takafumi FukushimaTakafumi Fukushima
Takafumi Fukushima
HHHideto Hashiguchi
Hideto Hashiguchi
HYHiroshi Yonekura
Hiroshi Yonekura
HKHisashi Kino
Hisashi Kino
MMMurugesan Mariappan
Murugesan Mariappan
MKMitsumasa Koyanagi
Mitsumasa Koyanagi
Plasma- and water-assisted oxide-oxide thermocompression direct bonding for a self-assembly based multichip-to-wafer (MCtW) 3D integration approach was demonstrated. The bonding yields and bonding strengths of the self-assembled chips obtained by the MCtW direct bonding technology were evaluated. In this study, chemical mechanical polish (CMP)-treated oxide formed by plasma-enhanced chemical vapor deposition (PE-CVD) as a MCtW bonding interface was mainly employed, and in addition, wafer-to-wafer thermocompression direct bonding was also used for comparison. N2 or Ar plasmas were utilized for the surface activation. After plasma activation and the subsequent supplying of water as a self-assembly mediate, the chips with the PE-CVD oxide layer were driven by the liquid surface tension and precisely aligned on the host wafers, and subsequently, they were tightly bonded to the wafers through the MCtW oxide-oxide direct bonding technology. Finally, a mechanism of oxide-oxide direct bonding to support the previous models was discussed using an atmospheric pressure ionization mass spectrometer (APIMS).

18 February 2011 in Micromachines
Verified
Journal Article
Open access
PDF file
Takafumi FukushimaTakafumi Fukushima
Takafumi Fukushima
TKTakayuki Konno
Takayuki Konno
EIEiji Iwata
Eiji Iwata
RKRisato Kobayashi
Risato Kobayashi
TKToshiya Kojima
Toshiya Kojima
MKMitsumasa Koyanagi
Mitsumasa Koyanagi
New surface mounting and packaging technologies, using self-assembly with chips having cavity structures, were investigated for three-dimensional (3D) and hetero integration of complementary metal-oxide semiconductors (CMOS) and microelectromechanical systems (MEMS). By the surface tension of small droplets of 0.5 wt% hydrogen fluoride (HF) aqueous solution, the cavity chips, with a side length of 3 mm, were precisely aligned to hydrophilic bonding regions on the surface of plateaus formed on Si substrates. The plateaus have micro-channels to readily evaporate and fully remove the liquid from the cavities. The average alignment accuracy of the chips with a 1 mm square cavity was found to be 0.4 mm. The alignment accuracy depends, not only on the area of the bonding regions on the substrates and the length of chip periphery without the widths of channels in the plateaus, but also the area wetted by the liquid on the bonding regions. The precisely aligned chips were then directly bonded to the substrates at room temperature without thermal compression, resulting in a high shear bonding strength of more than 10 MPa.

4 March 2020 in Japanese Journal of Applied Physics
Verified
Journal Article
Closed access
PDF file
MMMurugesan Mariappan
Murugesan Mariappan
KMKiyoharu Mori
Kiyoharu Mori
JBJichel Bea
Jichel Bea
MKMitsumasa Koyanagi
Mitsumasa Koyanagi
TFTakafumi Fukushima
Takafumi Fukushima
A feasibility study has been carried out to find an alternative method to the laborious cum expensive physical vapor deposition (PVD)/atomic layer deposition for the deposition of barrier and seed metal layers inside the deep Si trenches with aspect ratio (AR) greater than 10, by using low-cost, highly-scalable, CMOS-compatible electroless (EL) plating method to plate Ni as (barrier cum) seed layer for the fabrication of sub- μ m as well as 10 μ m width copper through-silicon-vias (Cu-TSVs). Micro-structural data revealed that both sub- μ m and 10 μ m width TSVs with AR ranging from 12 to 17 were completely filled with Cu by using EL-Ni as a seed layer. Further, both scanning electron microscope and energy dispersive X-ray analyzes data confirms the conformal formation of EL-Ni all through TSV sidewall and TSV bottom, which is otherwise difficult to realize by the even sophisticated PVD tool. Therefore, the EL plating method appears to be a highly promising method for the conformal formation of barrier/seed layers inside the high AR TSVs for future three-dimensional integration and packaging applications.

8 November 2017 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
HHHideto Hashiguchi
Hideto Hashiguchi
Takafumi FukushimaTakafumi Fukushima
Takafumi Fukushima
HHHiroyuki Hashimoto
Hiroyuki Hashimoto
JBJi-Cheol Bea
Ji-Cheol Bea
MMMurugesan Mariappan
Murugesan Mariappan
MKMitsumasa Koyanagi
Mitsumasa Koyanagi
A self-assembly and electrostatic (SAE) carrier technology is developed for high-precision and high-throughput chip-to-wafer 3-D integration. In this paper, water surface tension-driven chip assembly is combined with electrostatic adhesion to keep high alignment accuracies obtained by the capillary self-assembly process. The self-assembled chips can be firmly fixed on an SAE carrier wafer by electrostatic adhesion, and then, the chips can be readily detached from the carrier by discharging and transferred to another carrier with a temporary adhesive. This paper describes the impact of chip clamping forces and electrical reliability of the SAE carrier on chips to be 3-D stacked in chip-to-wafer configuration. Through-Si via formation is demonstrated by using a via-last 3-D integration process based on the SAE carrier. The demonstration shows that the SAE carrier maintains higher chip alignment accuracies than does conventional carrier without electrostatic adhesion.

22 February 2012 in Journal of Electronic Materials
Verified
Journal Article
Closed access
PDF file
MMMurugesan Mariappan
Murugesan Mariappan
YOY. Ohara
Y. Ohara
Takafumi FukushimaTakafumi Fukushima
Takafumi Fukushima
TTTetsu Tanaka
Tetsu Tanaka
MKM. Koyanagi
M. Koyanagi