Samir Čimić

Prof. Dr. Samir Čimić

School of Dental Medicine, University of Zagreb, Gunduliceva 5, 10000 Zagreb, Croatia
orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2019 in The Journal of Prosthetic Dentistry
Verified
Journal Article
Closed access
Vladimir PrpicVladimir Prpic
Vladimir Prpic
ISIvan Slacanin
Ivan Slacanin
ZSZdravko Schauperl
Zdravko Schauperl
ACAmir Catic
Amir Catic
Nikša DulčićNikša Dulčić
Nikša Dulčić
SČSamir Čimić
Samir Čimić

18 August 2023 in Dentistry Journal
Verified
Journal Article
Open access
PDF file
Vladimir PrpicVladimir Prpic
Vladimir Prpic
Filipa Špehar TomljenovićFilipa Špehar Tomljenović
Filipa Špehar Tomljenović
DŠDominik Štajdohar
Dominik Štajdohar
RBRoko Bjelica
Roko Bjelica
SČSamir Čimić
Samir Čimić
Matej ParMatej Par
Matej Par
Data regarding the mechanical properties of three-dimensionally (3D) printed materials for occlusal splint manufacturing are scarce. The aim of the present study was to evaluate the flexural strength and surface hardness of modern 3D-printed occlusal splint materials and compare them with two control groups, namely, milled and conventional cold-polymerized occlusal splint materials. A total of 140 rectangular specimens were manufactured for the present study. The specimens were prepared in accordance with the International Organization for Standardization standards (ISO 20795-1:2013). Five 3D-printed (NextDent Ortho Rigid, Dental LT Clear, Dentona Flexisplint, Cosmos Bite Splint, and ProArt Print Splint), one milled (ProArt CAD Splint), and one cold-polymerized (ProBase Cold) occlusal splint materials were used to determine flexural strength and surface hardness values. The three-point flexure test was used for the determination of flexural strength values, while Vickers hardness was measured to determine surface hardness. Ten specimens (n = 10) of each material were tested using these procedures. One-way ANOVA and Tukey’s post-hoc test were used to analyze the obtained results (α = 0.05). The values of flexural strength ranged from 46.1 ± 8.2 MPa to 106 ± 8.3 MPa. The Vickers hardness values ranged from 4.9 ± 0.5 VHN to 20.6 ± 1.3 VHN. Significant differences were found among the tested materials (p < 0.0001). The milled and cold-polymerized materials yielded higher values for both flexural strength (only one 3D-printed resin had comparable results to cold-polymerized acrylics) and surface hardness. There are differences in the mechanical properties of the various tested occlusal splint materials. The flexural strength of most of the 3D-printed materials and their surface hardness values are still inferior when compared to the milled or cold-polymerized materials.

1 January 2020 in The Journal of Advanced Prosthodontics
Verified
Journal Article
Open access
PDF file
Vladimir PrpicVladimir Prpic
Vladimir Prpic
ZSZdravko Schauperl
Zdravko Schauperl
DGDOMAGOJ GLAVINA
DOMAGOJ GLAVINA
Amir CaticAmir Catic
Amir Catic
SČSamir Čimić
Samir Čimić
Prpić V, et al. J Adv Prosthodont. 2020 Dec;12(6):376-382. https://doi.org/10.4047/jap.2020.12.6.376

10 July 2025 in Dentistry Journal
Verified
Journal Article
Open access
PDF file
LŠLuka Šimunović
Luka Šimunović
SČSamir Čimić
Samir Čimić
Senka MeštrovićSenka Meštrović
Senka Meštrović
Three-dimensional (3D) printing has emerged as a transformative technology in dental splint fabrication, offering significant advancements in customization, production speed, material efficiency, and patient comfort. This comprehensive review synthesizes the current literature on the clinical use, benefits, limitations, and future directions of 3D-printed dental splints across various disciplines, including prosthodontics, orthodontics, oral surgery, and restorative dentistry. Key 3D printing technologies such as stereolithography (SLA), digital light processing (DLP), and material jetting are discussed, along with the properties of contemporary photopolymer resins used in splint fabrication. Evidence indicates that while 3D-printed splints generally meet ISO standards for flexural strength and wear resistance, their mechanical properties are often 15–30% lower than those of heat-cured PMMA in head-to-head tests (flexural strength range 50–100 MPa vs. PMMA 100–130 MPa), and study-to-study variability is high. Some reports even show significantly reduced hardness and fatigue resistance in certain resins, underscoring material-specific heterogeneity. Clinical applications reviewed include occlusal stabilization for bruxism and temporomandibular disorders, surgical wafers for orthognathic procedures, orthodontic retainers, and endodontic guides. While current limitations include material aging, post-processing complexity, and variability in long-term outcomes, ongoing innovations—such as flexible resins, multi-material printing, and AI-driven design—hold promise for broader adoption. The review concludes with evidence-based clinical recommendations and identifies critical research gaps, particularly regarding long-term durability, pediatric applications, and quality control standards. This review supports the growing role of 3D printing as an efficient and versatile tool for delivering high-quality splint therapy in modern dental practice.

1 June 2016 in The Journal of Prosthetic Dentistry
Verified
Journal Article
Closed access
SČSamir Čimić
Samir Čimić
SSSonja Kraljević Simunković
Sonja Kraljević Simunković
Amir CaticAmir Catic
Amir Catic

3 February 2018 in European Journal of Pediatrics
Verified
Journal Article
Closed access
PDF file
AMAna Savic Mlakar
Ana Savic Mlakar
IHIva Hojsak
Iva Hojsak
MJMladen Jergović
Mladen Jergović
SČSamir Čimić
Samir Čimić
KBKrešo Bendelja
Krešo Bendelja