Karol Osowski

Dr. Karol Osowski


Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 October 2018 in Journal of Intelligent Material Systems and Structures
Verified
Journal Article
Open access
PDF file
AOArtur Olszak
Artur Olszak
KOKarol Osowski
Karol Osowski
ZKZbigniew Kesy
Zbigniew Kesy
AKAndrzej Kesy
Andrzej Kesy
This article presents the results of experimental investigations and simulations for a new design of a hydrodynamic clutch with a magnetorheological working fluid. The concept of magnetorheological fluid applications to improve the performance of a hydrodynamic clutch can be realized using resistant flow control inside a hydrodynamic clutch channel by changing the fluid shear stress with magnetic fields. The increase in the shear stress of a working fluid under a magnetic field causes an increase in the pressure drop in the channels, an increase in the flow losses, and a decrease in the transmitted power. Moreover, the steady-state and dynamic characteristics of the clutch are presented and the relations that occur between the design parameters are shown.

9 August 2017 in Smart Materials and Structures
Verified
Journal Article
Closed access
PDF file
EZE Ziabska
E Ziabska
JDJ Duchowski
J Duchowski
AOA Olszak
A Olszak
KOKarol Osowski
Karol Osowski
AKA Kesy
A Kesy
Seung-Bok ChoiSeung-Bok Choi
Seung-Bok Choi
The paper presents experimental results concerning the wear of heterogeneous electro-rheological (ER) fluids operating as working fluids in a complex clutch system consisting of a hydrodynamic clutch and a cylinder viscous clutch. The change of electric field intensity in the clutches results in change of sheer stress values in working fluids what causes the change of transmitted torque. This work shows that the most important factors affecting the wear of the ER fluid are the electric field of high intensity, the accompanying electrical breakdown, and the high temperature of the silicone oil. In addition, the water from the humid air absorbed mainly by hygroscopic particles influences a significant impact on the wear of the working fluid. Various forms of wear particles of the fluid depending on the prevailing conditions such as working mode are observed from the microscopic aspects. It is observed that the particles are flattened, rolled out or smashed into smaller fragments, partially melted, wrinkled and glued or caked. In addition, it is identified that the partial destruction of silicone oil is occurred due to the damage of the hydrocarbon chains, as evidenced by the decrease in its viscosity and the presence of the particle matter newly containing silicon.

6 January 2019 in Journal of Intelligent Material Systems and Structures
Verified
Journal Article
Closed access
AOArtur Olszak
Artur Olszak
KOKarol Osowski
Karol Osowski
ZKZbigniew Kęsy
Zbigniew Kęsy
AKAndrzej Kęsy
Andrzej Kęsy
The article concerns steady-state characteristics of a hydrodynamic clutch with electrorheological working fluid controlled by changes in strength of electric field and changes in the filling degree. The characteristics were obtained by experimenting, as well as calculations based on one-dimensional mathematical models. While creating the mathematical models, factors taken into consideration included differences between methods controlling the clutch, as well as various ways the working fluid flows in the clutch’s working space, depending on the relation of angular speed of rotors. The resultant mathematical models were verified with experimental research.

26 April 2024 in Micromachines
Verified
Journal Article
Open access
PDF file
KMKarol Musiałek
Karol Musiałek
IMIreneusz Musiałek
Ireneusz Musiałek
KOKarol Osowski
Karol Osowski
AOArtur Olszak
Artur Olszak
AMAneta Mikulska
Aneta Mikulska
Seung-Bok ChoiSeung-Bok Choi
Seung-Bok Choi
This paper presents a new type of hydraulic clutch operating by means of magnetorheological (MR) fluids and the results achieved from both theoretical analysis and experimental measurement. A hydraulic clutch system with MR working fluid and a rotating magnetic field located was designed. The clutch was based on the principle of using a rotating magnetic field created by an alternating current electromagnet to set the MR fluid in motion. To test the hydraulic clutch with a rotating magnetic field, MR fluids were produced by our laboratory, consisting of solid iron particles of various diameters mixed with a silicone oil. With MR working fluid and a rotating magnetic core was designed. The rheological properties of the MR fluids were assessed on the basis of tests carried out with a Brookfield DV2T rheometer equipped with a magnetic device for generating a magnetic field. The characteristics of the hydraulic clutch were tested on a specially built test stand. It was found that the torque transmitted by the clutch increased with the rotational speed of the magnetic field and with a lower rotational speed of the beaker in which the working fluid was placed. It was also found that the greatest torque occurred with the working fluid with the highest iron content. Based on the analysis of the structure and characteristics of the clutch in which the magnetic field is used, it has been shown that the design of the developed clutch is similar to that of an induction clutch, and its characteristics correspond to the characteristics of the eddy current clutch. Therefore, the proposed new clutch with MR fluid and rotating magnetic field can be applied to stationary power transmission systems in a manner similar to an eddy current clutch.

7 August 2023 in Sensors
Verified
Journal Article
Open access
PDF file
TSTomasz Spotowski
Tomasz Spotowski
KOKarol Osowski
Karol Osowski
IMIreneusz Musiałek
Ireneusz Musiałek
AOArtur Olszak
Artur Olszak
AKAndrzej Kęsy
Andrzej Kęsy
Seung-Bok ChoiSeung-Bok Choi
Seung-Bok Choi
The paper presents the application of a strain gauge sensor and a viscous brake filled with an electrorheological (ER) fluid, which is a smart material with controlled rheological properties, by an electric field to the fluid domain. For experimental tests, a cylindrical viscous brake was designed. The tests were carried out on a test stand especially prepared for this purpose and suitable for the examination of the impact of the rotational speed of the input shaft and the value of the electric voltage supplied to the viscous brake on pressing forces, taking into account the ER fluid temperature and brake fluid filling level. On the basis of the experimental research results, a viscous brake control system to exert constant pressing forces with feedback from a strain gauge sensor, based on the programmable logic controller, was designed and implemented. This system, using its own control algorithm, ensured a control pressing force within the assumed range, both during the constant and follow-up control. The measurement results obtained during the tests of the viscous brake designed to exert a force were presented in the form of time courses, showing the changes of the pressing force, the electric voltage applied to the brake and the rotational speed of the brake input shaft. The developed ER fluid brake control system with feedback was tested for constant and follow-up control, taking into account the impact of the working fluid temperature. During the test it was possible to obtain a maximum pressing force equal to 50 N for an electric voltage limited to 2.5 kV. The resultant error was lower than 1 N, wherein the adjustment time after changing the desired value of the force was around 1.5 s. The correct operation of both the brake and the control system, as well as the compatibility of the pressing force value and time adjustment, were determined. The main technical contribution described in this article is the design of a new type of DECPF and a new method for its control with the use of a specifically programmed programmable logic controller which simulates the proportional-integral controllers’ operation.

18 December 2020 in Applied Sciences
Verified
Journal Article
Open access
PDF file
AOArtur Olszak
Artur Olszak
KOKarol Osowski
Karol Osowski
IMIreneusz Musiałek
Ireneusz Musiałek
ERElżbieta Rogoś
Elżbieta Rogoś
AKAndrzej Kęsy
Andrzej Kęsy
ZKZbigniew Kęsy
Zbigniew Kęsy
This paper presents the results of physicochemical and tribological tests of vegetable oils obtained by the supercritical fluid extraction method from berry seeds. The research was conducted by using these oils as the raw material for the biodegradable hydraulic working fluids. The oils were assessed in terms of kinematic viscosity, anti-wear properties, resistance to oxidation and corrosive effects to copper and the pour point. The best results were achieved in the case of the blackcurrant seed oil. In order to confirm the practical possibility of using vegetable oils as working fluids for hydraulic couplings, experimental tests of the hydrodynamic clutch filled with blackcurrant seed oil were carried out. Based on the obtained research results, it was found that oils from berry plant seeds produced by supercritical extraction could be used in the future as potential working fluids for hydraulic systems.