This paper presents a new type of hydraulic clutch operating by means of magnetorheological (MR) fluids and the results achieved from both theoretical analysis and experimental measurement. A hydraulic clutch system with MR working fluid and a rotating magnetic field located was designed. The clutch was based on the principle of using a rotating magnetic field created by an alternating current electromagnet to set the MR fluid in motion. To test the hydraulic clutch with a rotating magnetic field, MR fluids were produced by our laboratory, consisting of solid iron particles of various diameters mixed with a silicone oil. With MR working fluid and a rotating magnetic core was designed. The rheological properties of the MR fluids were assessed on the basis of tests carried out with a Brookfield DV2T rheometer equipped with a magnetic device for generating a magnetic field. The characteristics of the hydraulic clutch were tested on a specially built test stand. It was found that the torque transmitted by the clutch increased with the rotational speed of the magnetic field and with a lower rotational speed of the beaker in which the working fluid was placed. It was also found that the greatest torque occurred with the working fluid with the highest iron content. Based on the analysis of the structure and characteristics of the clutch in which the magnetic field is used, it has been shown that the design of the developed clutch is similar to that of an induction clutch, and its characteristics correspond to the characteristics of the eddy current clutch. Therefore, the proposed new clutch with MR fluid and rotating magnetic field can be applied to stationary power transmission systems in a manner similar to an eddy current clutch.
The paper presents a new type of hydraulic clutch operating with magnetorheological (MR) fluids and the results achieved from both theoretical analysis and experimental measurement. The hy-draulic clutch system of its own design with MR working fluid and a rotating magnetic field lo-cated is designed. The principle of this clutch is to use a rotating magnetic field created by an al-ternating current electromagnet to set the MR fluid in motion. In the tests of the hydraulic clutch with a rotating magnetic field, MR fluid produced on their own, consisting of solid iron particles of various diameters mixed with a silicone oil, are used as working fluids. The rheological properties of MR fluids are assessed on the basis of tests carried out with a Brookfield DV2T rheometer equipped with a magnetic device for generating the magnetic field of its own design. The char-acteristics of the hydraulic clutch with MR working fluid and the rotating magnetic field are tested on a specially built test stand. As a result of the research, it has been found that the torque transmitted by the clutch is the greater, the higher the rotational speed of the magnetic field and the lower the rotational speed of the beaker in which the working fluid is placed, and that the greatest torque occurs for the working fluid with the highest iron content. Based on the analysis of the structure and characteristics of the clutch in which the magnetic field is used, it has been shown that the design of the developed clutch is similar to that of an induction clutch, and its characteristics correspond to the characteristics of the eddy current clutch. Therefore, the proposed new clutch working with MR fluid and the rotating magnetic field can be applied to stationary power transmission system similarly to an eddy current clutch.
The article studies the wear an ecological electrorheological fluid caused by the occurrence of electricalbreakdowns. The fluid studied– eER1–is composed of organic solid particles, vegetable oil, and water, whichis included to enhance its electrical properties. A special device was built for the destruction of the eER1 fluid.The study involves the preparation (using several measuring devices of different designs) and comparison ofthe rheological characteristics performed for valve and shear flow, for both unused and used eER1 fluid. Basedon the analysis of the study results, the causes and extent of wear in the tested ecological electrorheologicalfluid were identified, and general conclusions were drawn.
16 July 2026 in Journal of Sustainable Technologies
This paper evaluates the feasibility of assessing the wear degree of an electrorheological fluid based on the changes in particle size distribution. The investigated material was a two-phase electrorheological fluid composed of polymer solid particles dispersed in silicone oil. Fluid wear was simulated under controlled operating conditions using a specially designed test rig that reproduced laminar flow and cyclic electrical breakdowns, reflecting the actual working environment of hydraulic components utilising electrorheological fluids. Samples of fresh liquid and liquid used for up to three months were analysed by laser diffraction spectroscopy with a particle size analyser. The particle size distributions revealed a progressive degradation of the solid phase during wear. Wear processes caused fragmentation of larger particles, resulting in an increased fraction of fine and medium-sized particles and a reduction in coarse particles. Changes in cumulative particle size distributions confirmed a systematic shift toward smaller particle diameters with an increasing operating time. At the same time, high-temperature electrical breakdowns promoted secondary agglomeration and formation of very fine carbonised particles, contributing to sludge formation and an altered fluid consistency. The results demonstrate that wear of electrorheological fluid is gradual and cumulative rather than sudden. Particle size distribution analysis proved to be a sensitive and effective diagnostic tool for monitoring degradation of electrorheological fluids during operation. The proposed method can therefore be applied for technical condition assessment, durability evaluation, and predictive maintenance of hydraulic devices employing electrorheological working fluids.