A method of measuring the power line wire sag using optical sensors that are insensitive to high electromagnetic fields was proposed. The advantage of this technique is that it is a non-invasive measurement of power line wire elongation using a unique optomechanical system. The proposed method replaces the sag of the power line wire with an extension of the control sample and then an expansion of the attached chirped fiber Bragg grating. This paper presents the results of the first measurements made on real aluminum-conducting steel-reinforced wire, frequently used for power line construction. It has been shown that the proper selection of the CFBG (chirped fiber Bragg grating) transducer and the appropriate choice of optical parameters of such a sensor will allow for high sensitivity of the line wire elongation and sag while reducing the sensitivity to the temperature. It has been shown that with a simple optomechanical system, a non-invasive measurement of the power line wire sag that is insensitive to temperature changes and the influence of high electromagnetic fields can be achieved.

In this paper, we present a method for the simultaneous measurement of rotation and displacement or rotation and bending using single tilted fiber Bragg grating (TFBG). The insensitivity of the proposed system to temperature changes and the stretching direction of the fiber section in the sensing structure have been demonstrated. The experimentally determined sensitivities for rotation, displacement and bending are as follows: −0.0018 1/deg., 0.0054 nm/mm, and −0.055 1/mm over the measurement ranges of approximately 25-80 degrees, 34-74 mm, and 26.4-20 mm, respectively. The presented measurement system is versatile due to the ability to tune the measurement range by changing the fiber-loop radius.

During the operation of solar and wind power plants, it is necessary to solve issues related to the guaranteed capacity of these plants, as well as the frequency stabilisation in the power system where they operate, and maintain an operating mode of self-sufficiency conditions. One of the solutions to these problems is the use of energy storage systems. This article proposes a mathematical model for the study of frequency and power regulation processes in power systems with distributed generation, which includes renewable energy resources and energy storage systems. The novelty of the model lies in the possibility of determining energy cost indicators based on instantaneous energy power data. The model allows us to estimate the conditions under which distributed generation becomes self-sufficient. The results of the model calculations of two variants of power system operation, which includes wind generators with a capacity of 1500 MW, demonstrate the ability of the proposed model to accurately reproduce the dynamics of the frequency stabilisation process. The calculation results of the energy-economic indicators of a real power system combined with a powerful subsystem of wind generation and a battery-type energy storage system prove the competitiveness of self-sufficient renewable energy power plants.

Individual anatomical features of the paranasal sinuses and dentoalveolar system, the complexity of physiological and pathophysiological processes in this area, and the absence of actual standards of the norm and typical pathologies lead to the fact that differential diagnosis and assessment of the severity of the course of odontogenic sinusitis significantly depend on the measurement methods of significant indicators and have significant variability. Therefore, an urgent task is to expand the diagnostic capabilities of existing research methods, study the significance of the measured indicators, and substantiate the expediency of their use in the diagnosis of specific pathologies in an automated mode. Methods of digital filtering, image segmentation and analysis, fluid dynamics, and statistical and discriminant analysis were used. Preliminary differential diagnosis of odontogenic sinusitis can be performed by densitemetric analysis of tomographic images of the maxillary sinuses, performed using frontal multiplanar reconstructions according to a given algorithm. The very manifestation of the characteristic changes in the densitography of the maxillary sinus allows for the initiation of certain pathological processes and permits the development of the effectiveness of the diagnosis of the pathology of the sinus sinuses, which can be realized automatically in real life.

This paper presents a method for measuring two components of bending force and temperature using one sensor head. Indirect inference based on the spectra of two fiber Bragg gratings (FBGs) placed on a cantilever beam is used. The method was developed during work on the inverse problem of determining a nonuniform stress distribution based on FBG spectra. A gradient in the FBG stress profile results in a characteristic shape of its reflective spectrum. The simultaneous measurements of force and temperature were possible through the use of an appropriate layout of the sensor head. The spectral characteristics of the sensor’s gratings do not retain full symmetry, which is due to the geometry of the sensor’s head and the related difference in the distribution of the axial stress of the gratings. In the proposed approach, the change in width of the sum of the normalized transmission spectra was used to determine the value of the applied force. In the presented method, an increase in the sensitivity of this change to the force is obtained relative to the other known systems. A change in the spectral width was observed for an increase in bending forces from 0 to 150 N. The sensitivity coefficient of the spectral width to force, defined as the ratio of the change of the spectral half-width to the change in force was $2.6\mathrm{e}-3\mathrm{nm}/\mathrm{N}$ for the first grating and $1.2\mathrm{e}-3\mathrm{nm}/\mathrm{N}$ for the second grating. However, the sensitivity of the whole sensor system was $5.8\mathrm{e}-3\mathrm{nm}/\mathrm{N}$, which is greater than the sum of the sensitivities of the individual gratings. For the purpose of this work, a station with a thermal chamber has been designed with a bracket on which fiber optic transducers have been mounted for use in further measurements. The sensor head in this experiment is considered to be a universal device with potential applications in other types of optical sensors, and it can be treated as a module for development through its multiplication on a single optical fiber.

This study analyzes the existing methods for studying nasal breathing. The aspects of verifying the results of rhinomanometric diagnostics according to the data of spiral computed tomography are considered, and the methodological features of dynamic posterior active rhinomanometry and the main indicators of respiration are also analyzed. The possibilities of testing respiratory olfactory disorders are considered, the analysis of errors in rhinomanometric measurements is carried out. In the conclusions, practical recommendations are given that have been developed for the design and operation of tools for functional diagnostics of nasal breathing disorders. It is advisable, according to the data of dynamic rhinomanometry, to assess the functioning of the nasal valve by the shape of the air flow rate signals during forced breathing and the structures of the soft palate by the residual nasopharyngeal pressure drop. It is imperative to take into account not only the maximum coefficient of aerodynamic nose drag, but also the values of the pressure drop and air flow rate in the area of transition to the turbulent quadratic flow regime. From the point of view of the physiology of the nasal response, it is necessary to look at the dynamic change to the current mode, given the hour of the forced response, so that it will ensure the maximum possible acidity in the legend. When planning functional rhinosurgical operations, it is necessary to apply the calculation method using computed tomography, which makes it possible to predict the functional result of surgery.