Felix Grimm

Dr. Felix Grimm


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 January 2021 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
OSOliver Schmitz
Oliver Schmitz
SKSascha Kaiser
Sascha Kaiser
HKHermann Klingels
Hermann Klingels
PKPetra Kufner
Petra Kufner
MOMartin Obermüller
Martin Obermüller
MHMirko Hornung
Mirko Hornung
Recognizing the attention currently devoted to the environmental impact of aviation, this three-part publication series introduces two new aircraft propulsion concepts for the timeframe beyond 2030. The first part focuses on the novel steam injecting and recovering aero engine concept. In the second part, the free-piston composite cycle engine (FP-CCE) concept is presented. Complementary to the two technical publications, this third part describes the cooperative project, which was initiated by an interdisciplinary consortium, aiming at the demonstration and the proof-of-concept of both aforementioned aero engine concepts. At the beginning of the project, simulations on propulsion, aircraft system, and test bench level will be conducted. On this basis, preliminary tests and fundamental experiments are planned in order to establish a solid basis for the demonstration. Finally, a system demonstration will be carried out at the laboratory level. Thus, the project allows for a final judgment on both the feasibility of the new concepts and the attainability of the requirements for future aircraft propulsion systems.

25 February 2022 in Energies
Verified
Journal Article
Open access
PDF file
FGFelix Grimm
Felix Grimm
Prediction of pollutant emissions is a key aspect of modern combustor design in energy conversion systems. In the presented work, a simple and robust model based on low-order reaction networks is applied to a FLOX® laboratory combustor at atmospheric conditions. The applied approach is computationally cheap and therefore highly suited for design studies. Steady-state CFD RANS simulations are carried out, serving as a basis for the network generation algorithm. CFD results are validated with experimental data for flow field and combustion. Different degrees of fidelity of reactor network models are taken into consideration and findings are opposed to measurements, evaluating the quality of the low-fidelity models. Validation of CO and NOx emission results of reactor network modeling provides accurate qualitative and quantitative reproduction of experimental findings, depending on the degree of heat loss applied on the combustion system. The introduced approach is therefore readily applicable to large-scale, industrial, and gas turbine combustion.

21 January 2021 in Energies
Verified
Journal Article
Open access
PDF file
FGFelix Grimm
Felix Grimm
TLTimo Lingstädt
Timo Lingstädt
PKPeter Kutne
Peter Kutne
MAManfred Aigner
Manfred Aigner
An atmospheric prototype burner is studied with numerical and experimental tools. The burner system is designed for operation in a hybrid power plant for decentralized energy conversion. In order to realize such a coupled system, a reliable combustion system has to be established. Numerical and experimental findings in the presented study demonstrate the capabilities of the novel burner system in suitable operation conditions. In this system, a solid oxide fuel cell (SOFC) is mounted upstream of the burner in the gas turbine system. The combination of both realizes a large operational flexibility with comparably high overall efficiency. Since the combustor is operated with SOFC off-gas, several challenges arise. Low calorific combustion needs careful burner design and numerical modeling, since the heat-loss mechanisms occur to be in the order of magnitude of thermal power output. Thus, different modeling strategies are discussed in the paper. The numerical studies are compared with experimental results and high-quality simulation results complement limited measured findings with easy-to-use low fidelity RANS models. A priori measurements are employed for the selection of investigation points. It is shown that the presented combustor system is able to cover low-calorific combustion over a large range of operation conditions, despite major heat-loss effects, which are characterized by means of numerical CFD (Computational Fluid Dynamics) modeling.

3 February 2020 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
HBHannah E. Bower
Hannah E. Bower
ASAndreas Schwärzle
Andreas Schwärzle
FGFelix Grimm
Felix Grimm
TZTimo Zornek
Timo Zornek
PKPeter Kutne
Peter Kutne
With the push to curb dangerous atmospheric pollutant production, energy generation technologies that reduce green-house gas emissions, while still providing adequate electrical supply, are of high importance. With major energy infrastructure already in place, developing enhanced pollutant-reducing combustor systems for micro gas turbines (MGTs), that can utilize low calorific fuels from renewable resources, is a major goal. The current work focuses on the experimental testing of an optimized two-stage combustor designed to operate with various fuel types, including natural gas and syngas produced via biomass gasification. Atmospheric experimental tests were performed and the results indicate larger flame lift-off heights and slightly higher CO gas emissions levels, while displaying lower NOx gas emissions levels for all thermal loads and air-to-fuel equivalence ratios tested, compared to that of the previous combustor designs. Additionally, steady-state computational fluid dynamics (CFD) simulations were conducted and the results are in general good agreement with the experimental data. Overall, the results indicate high fuel flexibility of the combustor, as well as the ability to comply with the NOx emissions limits for a larger range of operating points, compared to that of the previously tested combustors.

31 March 2021 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
SISaeed Izadi
Saeed Izadi
JZJan Zanger
Jan Zanger
OKOliver Kislat
Oliver Kislat
BEBenedict Enderle
Benedict Enderle
FGFelix Grimm
Felix Grimm
MAManfred Aigner
Manfred Aigner
As an alternative to the commonly used swirl burners in microgas turbines (MGT), the FLOX®-based combustion concept promises great potential for the nitric oxide emission reduction and increased fuel flexibility. Despite having to deal with a new set of challenges while utilizing liquid fuel in the burner, first steps are taken to gain more information on the influencing operational parameters. In this regard, a FLOX®-based liquid fuel burner is developed to fit into a newly designed combustor for the Capstone C30 MGT. The C30 combustor operates with three burners arranged tangentially to an annular combustion chamber and provides a total thermal power of 115 kW. In this work, operational properties of merely one of the three C30 liquid fuel burners are investigated and the rest of the two burners are emulated in form of hot cross-flow. As for the liquid burners, the experiments are conducted with three geometrically different single-nozzle burners at atmospheric pressure. The cross-flow is realized by utilizing a 20–nozzle FLOX®-based natural gas combustor. Measurements include visualization of the reaction zone and analysis of the exhaust gas emissions. By detecting the hydroxyl radical chemiluminescence (OH*-CL) emissions, the position of the heat release zone within the combustion chamber is attained. Correspondingly, the flame height above burner and the flame length are calculated. The investigated design parameters include air preheat temperature up to 733 K, equivalence ratio, burner geometry, and thermal power. Through variation of thermal power, the effect of liquid fuel preparation, i.e., atomization, evaporation, and mixing on combustion properties and exhaust gas emissions are examined. The results show that the burners with the medium diameter consistently performed remarkably at different flame temperatures and thermal powers. The lowest NOx and CO emissions for the medium diameter burner lied between 5 to 7 ppm and 8 to 10 ppm, respectively.

9 June 2023 in Journal of the Global Power and Propulsion Society
Verified
Journal Article
Open access
Daniele CiriglianoDaniele Cirigliano
Daniele Cirigliano
HDHerol Lawerence D'SOuza
Herol Lawerence D'SOuza
FGFelix Grimm
Felix Grimm
PKPeter Kutne
Peter Kutne
MAManfred Aigner
Manfred Aigner
Micro Gas Turbines (MGTs) are nowadays largely used for electrical and thermal energy production in small buildings and households. Their reliability and compactness allow them to operate for thousands of hours with minimal maintenance. However, the long exposure at high temperatures in combustion chambers can promote creep, which can induce thermal fatigue and potential failure of these components. Creep-induced damage in MGTs has not yet been thoroughly investigated, due to the lack of numerical tools able to model these strongly coupled phenomena. This study presents the development of a Fortran-based subroutine integrated into ANSYS APDL. The code allows for a life assessment based on the Lemaitre-Chaboche creep damage model. Secondary creep and stress relaxation are modeled for the high-temperature resistant alloy Inconel718. A new set of temperature-dependent parameters for the Norton equation is provided, and the method to obtain these parameters from creep rupture tests is outlined. The model is validated and shows good agreement with experimental data. The subroutine correctly reproduces visco-plasticity, stress relaxation and damage under typical MGTs operating temperatures. This model constitutes the foundation of a life-assessment analysis for combustion chambers. The results highlight the impact of temperature and creep on the component’s life and the importance of integrating life assessment analysis into the preliminary design of combustion chambers.