Jan Zanger

Dr. Jan Zanger

orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 June 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
DSDaniel Silberhorn
Daniel Silberhorn
KDKatrin Dahlmann
Katrin Dahlmann
AGAlexander Görtz
Alexander Görtz
FLFlorian Linke
Florian Linke
JZJan Zanger
Jan Zanger
JHJohannes Hartmann
Johannes Hartmann
One of aviation’s major challenges for the upcoming decades is the reduction in its climate impact. As synthetic kerosene and green hydrogen are two promising candidates, their potentials in decreasing the climate impact is investigated for the mid-range segment. Evolutionary advancements for 2040 are applied, first with an conventional and second with an advanced low-NOx and low-soot combustion chamber. Experts and methods from all relevant disciplines are involved, starting from combustion, turbofan engine, overall aircraft design, fleet level, and climate impact assessment, allowing a sophisticated and holistic evaluation. The main takeaway is that both energy carriers have the potential to strongly reduce the fleet level climate impact by more than 75% compared with the reference. Applying a flight-level constraint of 290 and a cruise Mach number of 0.75, causing 5% higher average Direct Operating Costs (DOC), the reduction is even more than 85%. The main levers to achieve this are the advanced combustion chamber, an efficient contrail avoidance strategy, in this case a pure flight-level constraint, and the use of CO2 neutral energy carrier, in a descending priority order. Although vehicle efficiency gains only lead to rather low impact reduction, they are very important to compensate the increased costs of synthetic fuels or green hydrogen.

13 January 2021 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
OSOliver Schmitz
Oliver Schmitz
SKSascha Kaiser
Sascha Kaiser
HKHermann Klingels
Hermann Klingels
PKPetra Kufner
Petra Kufner
MOMartin Obermüller
Martin Obermüller
MHMirko Hornung
Mirko Hornung
Recognizing the attention currently devoted to the environmental impact of aviation, this three-part publication series introduces two new aircraft propulsion concepts for the timeframe beyond 2030. The first part focuses on the novel steam injecting and recovering aero engine concept. In the second part, the free-piston composite cycle engine (FP-CCE) concept is presented. Complementary to the two technical publications, this third part describes the cooperative project, which was initiated by an interdisciplinary consortium, aiming at the demonstration and the proof-of-concept of both aforementioned aero engine concepts. At the beginning of the project, simulations on propulsion, aircraft system, and test bench level will be conducted. On this basis, preliminary tests and fundamental experiments are planned in order to establish a solid basis for the demonstration. Finally, a system demonstration will be carried out at the laboratory level. Thus, the project allows for a final judgment on both the feasibility of the new concepts and the attainability of the requirements for future aircraft propulsion systems.

11 April 2011 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
JZJan Zanger
Jan Zanger
AWAxel Widenhorn
Axel Widenhorn
MAManfred Aigner
Manfred Aigner
Pressure losses between the compressor outlet and the turbine inlet are a major issue of overall efficiency and system stability for a solid oxide fuel cell/micro gas turbine (MGT) hybrid power plant system. The goal of this work is the detailed analysis of the effects of additional pressure losses on MGT performance in terms of steady-state and transient conditions. The experiments were performed using the micro gas turbine test rig at the German Aerospace Centre in Stuttgart using a butterfly control valve to apply additional pressure loss. This paper reports electric power and pressure characteristics at steady-state conditions as well as a new surge limit for this Turbec T100 micro gas turbine test rig. Furthermore, the effects of additional pressure loss on the compressor surge margin are quantified and a linear relation between the relative surge margin and additional pressure loss is shown. For transient variation of pressure loss at constant turbine speed, time delays are presented and an instability issue of the commercial gas turbine controller is discussed. Finally, bleed-air blow-off and reduction of the turbine outlet temperature are introduced as methods of increasing the surge margin. It is quantified that both methods have a substantial effect on the compressor surge margin. Furthermore, a comparison between both methods is given in terms of electric power output.

13 February 2018 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Open access
PDF file
TSTeresa Siebel
Teresa Siebel
JZJan Zanger
Jan Zanger
AHAndreas Huber
Andreas Huber
MAManfred Aigner
Manfred Aigner
KKKarsten Knobloch
Karsten Knobloch
FBFriedrich Bake
Friedrich Bake
Auxiliary power unit (APU) operators face increasingly stricter airport requirements concerning exhaust gas and noise emission levels. To simultaneously reduce exhaust gas and noise emissions and to satisfy the increasing demand of electric power on board, optimization of the current technology is necessary. Prior to any possible demonstration of optimization potential, detailed data of thermodynamic properties and emissions have to be determined. Therefore, the investigations presented in this paper were conducted at a full-scale APU of an operational aircraft. A Pratt & Whitney (East Hartford, CT) APS3200, commonly installed in the Airbus A320 aircraft family, was used for measurements of the reference data. In order to describe the APS3200, the full spectrum of feasible power load and bleed air mass flow combinations were adjusted during the study. Their effect on different thermodynamic and performance properties, such as exhaust gas temperature, pressure as well as electric and overall efficiency is described. Furthermore, the mass flows of the inlet air, exhaust gas, and fuel input were determined. Additionally, the work reports the exhaust gas emissions regarding the species CO2, CO, and NOx as a function of load point. Moreover, the acoustic noise emissions are presented and discussed. With the provided data, the paper serves as a database for validating numerical simulations and provides a baseline for current APU technology.

31 March 2021 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
HSHannah Seliger-Ost
Hannah Seliger-Ost
PKPeter Kutne
Peter Kutne
JZJan Zanger
Jan Zanger
MAManfred Aigner
Manfred Aigner
The use of biogas has currently two disadvantages. First, processing biogas to natural gas quality for feeding into the natural gas grid is a rather energy-consuming process. Second, the conversion into electricity directly in biogas plants produces waste heat, which largely cannot be used. Therefore, a feed-in of the desulfurized and dry biogas to local biogas grids would be preferable. Thus, the biogas could be used directly at the end consumer for heat and power production. As biogas varies in its methane (CH4) and carbon dioxide (CO2) content, respectively, this paper studies the influence of different biogas mixtures compared to natural gas on the combustion in a flameless oxidation (FLOX®)-based six nozzle combustor. The single staged combustor is suitable for use in a micro gas turbine (MGT) based combined heat and power (CHP) system with an electrical power output of 3 kW. The combustor is studied in an optically accessible atmospheric test rig, as well as integrated into the MGT system. This paper focuses on the influence of the admixture of CO2 to natural gas on the NOx and CO emissions. Furthermore, at atmospheric conditions, the shape and location of the heat release zone are investigated using OH* chemiluminescence (OH* CL). The combustor could be stably operated in the MGT within the complete stationary operating range with all fuel mixtures.

20 December 2023 in Journal of Engineering for Gas Turbines and Power
Verified
Journal Article
Closed access
PDF file
SISaeed Izadi
Saeed Izadi
JZJan Zanger
Jan Zanger
MBMartina Baggio
Martina Baggio
HSHannah Seliger-Ost
Hannah Seliger-Ost
PKPeter Kutne
Peter Kutne
MAManfred Aigner
Manfred Aigner
The effect of superheated liquid fuel injection on the performance and emissions of a single nozzle combustor was investigated. Combustion of the lean premixed flames was achieved using a combination of jet and swirl as a stabilization method. In a nonreactive setup, the optimum transition temperature of Jet A-1 fuel from liquid to superheated vaporized state was analyzed. In a subsequent reactive setup, a series of tests were conducted with the liquid fuel at low and elevated temperatures. The experiments were conducted at ambient pressure and various air and fuel preheat temperatures, axial swirlers, thermal powers, adiabatic flame temperatures, and flame tube diameters. Concentrations of nitric oxide (NOx) and carbon monoxide (CO) in the flue gas were measured. The operating conditions were systematically selected according to the design of experiments (DOE) method. The results showed that the adiabatic flame temperature caused the most significant change in combustion emissions and the position and shape of the reaction zone, while the superheated fuel injection had only a minor effect because the liquid fuel droplets were largely vaporized before entering the reaction zone through the integration of a swirler and a prefilmer. The use of the axial swirler and prefilmer allowed the combustor to operate in both spray and fully vaporized fuel conditions. As a result, very low emission concentrations of NOx (≈5 ppm) and CO (≈6 ppm) were achieved. The median flame length and height above the burner of the characterized flames showed competitive values of 32 mm and 50 mm, respectively. Lean blowout limits of less than 1500 K were achieved. Two different flame modes were observed during the experiments. By increasing the bulk velocity of the combustor, its hysteresis was resolved, resulting in stable and reliable flames with a wide low-NOx operating range.