In this study, graphene oxide (GO) nanosheets were modified with an amine functional group to obtain amine-functionalized graphene (AMG) nanosheets and then blended with the aniline curing agent of bisphenol-A (BPA) epoxy resin to crosslink BPA epoxy resin. The AMG-blended curing agent and BPA epoxy resin formed an intermolecular hydrogen bond that was stronger than the π–π stacking force between benzene rings of graphene nanosheets. Therefore, AMG nanosheets exhibited excellent dispersion in the aniline curing agent. The amine group of AMG-blended curing agents and the epoxy functional group of BPA epoxy resin exhibited strong chemical activity and underwent crosslinking and polymerization. AMG nanosheets were mixed with BPA epoxy resin to form a crosslinked structure through the epoxy ring-opening polymerization of the resin. The mechanical properties of the epoxy resin nanocomposites were significantly improved by the added 1 wt.% AMG nanosheets. The tensile strength was enhanced by 98.1% by adding 1 wt.% AMG in epoxy. Furthermore, the impact resistance of the epoxy resin was enhanced by 124.4% after adding 2.67 wt.% of AMG nanosheets. Compared with other reinforced fillers, AMG nanosheets are very light and can therefore be used as nanocomposite materials in coating applications, the automotive industry, aerospace sheet materials, wind power generation, and other fields.

The flexible surface-enhanced Raman scattering (SERS) sensor, which has the bionic 3D nanoarray structure of a beetle-wing substrate (BWS), was successfully prepared by replicated technology and thermal evaporation. The bionic structure was replicated with polydimethylsiloxane (PDMS) and then silver (Ag) nanoisland thin films were deposited by thermal evaporation. The deposition times and thicknesses (25–40 nm) of the Ag thin films were manipulated to find the optimal SERS detection capability. The Ag nanoisland arrays on the surface of the bionic replicated PDMS were observed by scanning electron microscope (SEM), X-ray diffraction (XRD), and contact angle, which can generate strong and reproducible three-dimensional hotspots (3D hotspots) to enhance Raman signals. The water pollutant, rhodamine 6G (R6G), was used as a model molecule for SERS detection. The results show that 35 nm Ag deposited on a PDMS-BWS SERS substrate displays the strongest SERS intensity, which is 10 times higher than that of the pristine BWS with 35 nm Ag coating, due to the excellent 3D bionic structure. Our results demonstrate that bionic 3D SERS sensors have the potential to be applied in wearable devices and sensors to detect biomolecules and environmental pollutants, such as industrial wastewater, in the future.

The results of studies on the corrosion protectiveness and thermal conductivity of reduced graphene oxide–BaSO₄ epoxy composites are reported here. A commercial epoxy resin and reduced graphene oxide (rGO) were blended with a hardening reagent and then mixed with prepared BaSO₄–epoxy resin (B–epoxy). The reduced graphene oxide–BaSO₄–epoxy composite (rGO–B–epoxy) paste was used to coat the surfaces of Al 7205 alloy and the corrosion and thermal properties were investigated. A corrosion test in a 3.5 wt% synthetic sea water solution showed that the composite coating containing BaSO₄ had the best corrosion resistance. Moreover, the rGO–B–epoxy composite showed better protection against corrosion than the epoxy alone. The rGO–B–epoxy composite with 5 wt% BaSO₄ had an in-plane coefficient of thermal conductivity of approximately 165.0 W/m K, and the in-plane thermal diffusivity was 71.38 mm²/s. In standard thermal conductivity tests, all three samples had values below 40 W/m K. The rGO–B–epoxy composites showed good surface corrosion protection and in-plane thermal conductivity.

Chromia-forming ferritic stainless steel (FSS) is a highly promising interconnect material for application in solid oxide fuel cells. In this study, initial oxidation of chromium oxides was performed at 500–800 °C to understand the evolution of materials at an early stage. The structural variations in oxide scales were analyzed through scanning electron microscopy, energy dispersive spectroscopy (EDS), transmission electron microscopy (TEM), X-ray diffractometry (XRD), laser confocal microscopy (LSCM), X-ray photoelectron spectroscopy (XPS), and Raman spectroscopy. Surface electrochemical properties were investigated through electrochemical impedance spectroscopy to understand how the heat treatment temperature affected surface impedance. Treatment temperatures higher than 700 °C facilitate the diffusion of Cr and Mn, thus allowing ferritic spinels to form on the surface and leading to high electrical conductivity.