Arthur de Oliveira Lima

Mr. Arthur de Oliveira Lima

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 September 2018 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
Verified
Journal Article
Closed access
PDF file
ALArthur de Oliveira Lima
Arthur de Oliveira Lima
MDMarcus S Dersch
Marcus S Dersch
YQYu Qian
Yu Qian
ETErol Tutumluer
Erol Tutumluer
JEJohn Riley Edwards
John Riley Edwards
Primarily being employed in ballasted bridge decks and tunnels, under-ballast mat applications have seen growth in the North American market as a solution to reduce the stress state of the ballast by lowering the track stiffness and reducing ground-borne vibrations. However, the German DIN 45673 standard is currently the sole reference procedure for quantifying under-ballast mat’s mechanical fatigue performance by using real ballast particles as a loading contact interface and is tailored to European loading characteristics. This presents challenges for testing materials intended for North American heavy haul freight lines implementing such procedures. Moreover, large intrinsic variability is present when employing the real ballast material as a loading contact interface. This work presents findings from laboratory mechanical fatigue experiments conducted on under-ballast mat samples based on DIN-recommended procedures. Two loading contact interfaces—ballast box and geometric ballast plate—and two load magnitudes—representing European mainline and North American heavy haul freight loading environments—were applied to the samples in this study. For all tests, no significant physical sample damage was observed after testing. Further, although significant immediate change in bedding modulus was observed for the North American-loaded samples, modulus changes in both test cases were similar when evaluated one week after the completion of the tests. In addition, gradation analysis of the ballast material revealed little impact other than particle surface wear. Finally, results from this work demonstrate that geometric ballast plate is an effective alternative for investigating under-ballast mat’s performance and should be useful for the future development of North American-recommended practices for testing under-ballast mats subjected to heavy haul loads.

10 March 2023 in Transportation Research Record: Journal of the Transportation Research Board
Verified
Journal Article
Closed access
MPMax Potvin
Max Potvin
MDMarcus Dersch
Marcus Dersch
JEJohn Riley Edwards
John Riley Edwards
ALArthur de Oliveira Lima
Arthur de Oliveira Lima
Longitudinal track resistance is one of the most critical parameters required to accurately analyze longitudinal load propagation and refine rail neutral temperature (i.e., stress-free temperature) maintenance practices. However, longitudinal track resistance has not been consistently defined and has been quantified using multiple methods that should not be conflated. This paper documents common definitions of longitudinal track resistance and the two methods regularly used for its quantification: track panel pull test (TPPT) and single rail break (SRB). Further, this paper documents the differences in mechanics between these methods, summarizes and discusses the critical factors influencing the longitudinal track resistance values found in the literature, and adds novel TPPT longitudinal track resistance values for timber sleeper track to address the current scarcity of data found in the literature. In summary, TPPT values provide insight into the mechanics of load propagation and pre-buckle analysis while the SRB values aid in the maintenance and restoration of rail neutral temperature after a rail break or destress. Additionally, the TPPT longitudinal track resistance values reported in the literature were independent of panel length, were influenced most by the presence of a vertical load, and were reduced by 25% when the ballast was disturbed. Finally, novel TPPT results indicated the longitudinal resistance of timber sleeper track was 19% lower than concrete sleeper track and that unfastened sleepers still transferred longitudinal load when the cribs were full and ballast was compacted.

11 May 2022 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
Verified
Journal Article
Closed access
RHRyan M Harrington
Ryan M Harrington
ALArthur de Oliveira Lima
Arthur de Oliveira Lima
RFRichard Fox-Ivey
Richard Fox-Ivey
TNThanh Nguyen
Thanh Nguyen
JLJohn Laurent
John Laurent
JEJ Riley Edwards
J Riley Edwards
Railroad track inspections conducted in accordance with federal regulations and internal railway operating practices result in significant labor costs and occupy valuable network capacity. These factors, combined with advancements in the field of machine vision, have encouraged a transition from human visual inspections to machine-based alternatives. Commercial machine vision technologies for railway inspection currently exist, and automated analysis approaches—which deliver objective results—are available in some systems. However, they are limited to a “pass/fail” approach through the detection of components which fail to meet maintenance or geometry thresholds, as opposed to being able to detect subtle changes in track conditions to identify evolving problems. To overcome these limitations, this paper presents results from the field deployment and validation of a system that pairs three-dimensional (3D) machine vision with automated change detection technology. The change detection approach uses a deep convolution neural network (DCNN) to accurately characterize track conditions between repeat runs. Current automated track inspection technologies were studied, and the applicability of change detection is discussed. The paper presents the process for 3D image capture, DCNN training, and evaluation by comparing DCNN results to an expert human evaluator. Finally, it presents change detection results for fastener presence and spike height. Results indicate that this technology can successfully identify fasteners and spikes with percent accuracies greater than 98% and that it can successfully generate change detection results for comparison of track condition among runs.

27 November 2019 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
Verified
Journal Article
Closed access
PDF file
JBJacob M Branson
Jacob M Branson
MDMarcus S Dersch
Marcus S Dersch
ALArthur de Oliveira Lima
Arthur de Oliveira Lima
JEJohn Riley Edwards
John Riley Edwards
JBJosue Cesar Bastos
Josue Cesar Bastos
The degradation of ballast particles and concrete crossties in heavy-haul railroad tracks poses problems such as inhibiting proper drainage and disturbing track geometry. under-tie pads offer a solution to reduce crosstie–ballast stresses by improving load distribution through the track structure and reducing pressures on ballast particles and the crosstie surface. Despite the emergence of under-tie pads on heavy-haul corridors, optimal characteristics for the reduction of the tie–ballast stress state have not been defined in literature. In this research, several under-tie pad products and generic materials with various thicknesses and hardnesses were studied to identify appropriate properties of under-tie pad products for pressure distribution. The findings from this research provide an insight into how material characteristics influence the pressure mitigation performance of under-tie pads. Results from this study indicate that thickness is the most crucial metric determining under-tie pad performance in reducing ballast degradation; hardness and material type also have an effect, but to a lesser degree.

29 July 2021 in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
Verified
Journal Article
Closed access
PDF file
MDMarcus Dersch
Marcus Dersch
MTMatheus Trizotto
Matheus Trizotto
JEJohn Riley Edwards
John Riley Edwards
ALArthur de Oliveira Lima
Arthur de Oliveira Lima
To address a recent challenge related to broken spikes in premium elastic fastening systems that have led to at least ten derailments and require manual walking inspections as well as build upon mechanistic-empirical (M-E) design principles for future fastening system component design, this paper quantifies the vertical, lateral, and longitudinal fastening system loads under revenue service traffic in a curve that has regularly experienced spike fastener fatigue failures. Previous data has indicated that the high rail of Track 3 experienced the most failures at this location. The data from this investigation sheds light into why failures are more predominant at this location than others and how the vertical, lateral, and longitudinal loads cannot be considered independently. Specifically, while the magnitude of the applied loading was the lowest on the high rail of Track 3, the threshold for failure was also the lowest given the operations at this location led to unloading of the high rail, thus indirectly highlighting the importance of friction within a fastening system. The data also show the high rail of Track 3 was subjected to the highest L/V load ratios and was an outlier in the typical lateral load reversals applied likely leading to spike stress reversals and thus a shorter fatigue life. Finally, based upon the data, it is recommended that to mitigate spike failures, as well as similar fastener challenges in other track types (e.g. rail seat deterioration, etc.) railroads should ensure trains operate close to the balance speed and use fastening system that transfer loads through friction. This study also provides novel data for M-E design of fastening systems.

6 March 2023 in Transportation Research Record: Journal of the Transportation Research Board
Verified
Journal Article
Closed access
MDMarcus Dersch
Marcus Dersch
MPMax Potvin
Max Potvin
ALArthur de Oliveira Lima
Arthur de Oliveira Lima
JEJohn Riley Edwards
John Riley Edwards
There are, on average, 12.5 Federal Railroad Administration reportable derailments per year on U.S. mainlines and sidings caused by “defective or missing spikes or rail fasteners.” Because fastener failures are most commonly caused by a combination of vertical, lateral, and longitudinal loads, it is important to quantify all loads placed on the fasteners to reduce the number of failed fasteners and increase rail safety. Multiple researchers have developed analytical models that leverage longitudinal track resistance and stiffness to quantify the fastener demands. Therefore, to support the refinement of these analytical models that leverage longitudinal track resistance and stiffness, track panel pull tests (TPPTs) were executed in the laboratory to expand on the values within the available literature. These TPPTs quantified the effect of sleeper type (i.e., timber versus concrete), given that 88% of previous studies have focused on concrete. Further, these novel tests quantified the effect of the fastening system, crib ballast height, shoulder width, and ballast condition on the panel’s longitudinal resistance and stiffness. From these experiments and the resulting analysis of data, multiple conclusions were drawn. For example, concrete sleeper panels exhibit 20% higher resistance than timber sleeper panels, disturbing ballast reduced the longitudinal resistance by 13% and stiffness by approximately 80%, and the crib, shoulder, and bottom ballast provide approximately 65%, 5%, and 30% of the total longitudinal resistance, respectively.