In this paper, a multilevel architecture able to interface an on-board computer with a generic UAV flight controller and its radio receiver is proposed. The computer board exploits the same standard communication protocol of UAV flight controllers and can easily access additional data, such as: (i) inertial sensor measurements coming from a multi-sensor board; (ii) global navigation satellite system (GNSS) coordinates; (iii) streaming video from one or more cameras; and (iv) operator commands from the remote control. In specific operating scenarios, the proposed platform is able to act as a “cyber pilot” which replaces the role of a human UAV operator, thus simplifying the development of complex tasks such as those based on computer vision and artificial intelligence (AI) algorithms which are typically employed in autonomous flight operations.

Unmanned aerial systems (UASs) have enormous potential in many fields of application, especially when used in combination with autonomous guidance. An open challenge for safe autonomous flight is to rely on a mapping system for local positioning and obstacle avoidance. In this article, the authors propose a radar-based mapping system both for obstacle detection and for path planning. The radar equipment used is a single-chip device originally developed for automotive applications that has good resolution in azimuth, but poor resolution in elevation. This limitation can be critical for UAS application, and it must be considered for obstacle-avoidance maneuvers and for autonomous path-planning selection. However, the radar-mapping system proposed in this paper was successfully tested in the following different scenarios: a single metallic target in grass, a vegetated scenario, and in the close proximity of a ruined building.

In this paper, solutions for precise maneuvering of an autonomous small (e.g., 350-class) Unmanned Aerial Vehicles (UAVs) are designed and implemented from smart modifications of non expensive mass market technologies. The considered class of vehicles suffers from light load, and, therefore, only a limited amount of sensors and computing devices can be installed on-board. Then, to make the prototype capable of moving autonomously along a fixed trajectory, a “cyber-pilot”, able on demand to replace the human operator, has been implemented on an embedded control board. This cyber-pilot overrides the commands thanks to a custom hardware signal mixer. The drone is able to localize itself in the environment without ground assistance by using a camera possibly mounted on a 3 Degrees Of Freedom (DOF) gimbal suspension. A computer vision system elaborates the video stream pointing out land markers with known absolute position and orientation. This information is fused with accelerations from a 6-DOF Inertial Measurement Unit (IMU) to generate a “virtual sensor” which provides refined estimates of the pose, the absolute position, the speed and the angular velocities of the drone. Due to the importance of this sensor, several fusion strategies have been investigated. The resulting data are, finally, fed to a control algorithm featuring a number of uncoupled digital PID controllers which work to bring to zero the displacement from the desired trajectory.

Autonomous unmanned aerial systems (UAS) are having an increasing impact in the scientific community. One of the most challenging problems in this research area is the design of robust real-time obstacle detection and avoidance systems. In the automotive field, applications of obstacle detection systems combining radar and vision sensors are common and widely documented. However, these technologies are not currently employed in the UAS field due to the major complexity of the flight scenario, especially in urban environments. In this paper, a real-time obstacle-detection system based on the use of a 77 GHz radar and a stereoscopic camera is proposed for use in small UASs. The resulting system is capable of detecting obstacles in a broad spectrum of environmental conditions. In particular, the vision system guarantees a high resolution for short distances, while the radar has a lower resolution but can cover greater distances, being insensitive to poor lighting conditions. The developed hardware and software architecture and the related obstacle-detection algorithm are illustrated within the European project AURORA. Experimental results carried out employing a small UAS show the effectiveness of the obstacle detection system and of a simple avoidance strategy during several autonomous missions on a test site.

In recent years, the issue of trajectory planning for autonomous unmanned aerial vehicles (UAVs) has received significant attention due to the rising demand for these vehicles across various applications. Despite advancements, real-time trajectory planning remains computationally demanding, particularly with the inclusion of 3D localization using computer vision or advanced sensors. Consequently, much of the existing research focuses on semi-autonomous systems, which rely on ground assistance through the use of external sensors (motion capture systems) and remote computing power. This study addresses the challenge by proposing a fully autonomous trajectory planning solution. By introducing a real-time path planning algorithm based on the minimization of the snap, the optimal trajectory is dynamically recalculated as needed. Evaluation of the algorithm’s performance is conducted in an unknown real-world scenario, utilizing both simulations and experimental data. The algorithm was implemented in MATLAB and subsequently translated to C++ for onboard execution on the drone.

In this work, the authors propose a novel electronic architecture named VESTA (Versatile External Synchronization and Telemetry Architecture), capable of independently estimating position and attitude with centimeter-level accuracy, specifically designed to be mounted as a payload for multicopter drones. VESTA integrates GPS-RTK and inertial-sensing technologies to generate a high-precision telemetry data stream, which is transmitted via a dedicated UART (Universal Asynchronous Receiver-Transmitter) interface. The key innovation of VESTA lies in its robust temporal synchronization mechanism: by exploiting GPS time signals, including UTC timestamps and PPS (Pulse Per Second) signals, each telemetry sample is uniquely timestamped with millisecond resolution. To the best of our knowledge, current commercial and custom drone navigation systems lack a reliable method for achieving this level of absolute time synchronization between inertial and GNSS data. This limitation hinders precise data fusion and complicates integration with other systems requiring temporally aligned information. VESTA addresses this gap, enabling accurate and unambiguous time correlation across subsystems. The positioning accuracy and synchronization performance of VESTA were validated through comparative testing with the DJI Matrice 300 RTK, one of the most advanced commercial UAS platforms, which notably does not support GPS-based timestamping. A Leica total station, providing millimeter-level ground truth, was employed to track the drone’s trajectory and quantitatively assess the estimation errors of both systems.