The hot deformation behaviors of a Ti46Al2Cr2Nb alloy were investigated at strain rates of 0.001–0.1 s⁻¹ and temperatures of 910–1060 °C. Under given deformation conditions, the activation energy of the TiAl alloy could be estimated as 319 kJ/mol. The experimental results were predicted by different predictive models including three constitutive models and three data-driven models. The most accurate data-driven model and constitutive model were an artificial neural network (ANN) and an Arrhenius type strain-compensated Sellars (SCS) model, respectively. In addition, the generalization capability of ANN model and SCS model was examined under different deformation conditions. Under known deformation conditions, the ANN model could accurately predict the flow stress of TiAl alloys at interpolated and extrapolated strains with a coefficient of determination (R²) greater than 0.98, while the R² value of the SCS model was smaller than 0.5 at extrapolated strains. However, both ANN and SCS models performed poorly under new deformation conditions. A hybrid model based on the SCS model and ANN predictions was shown to have a wider generalization capability. The present work provides a comprehensive study on how to choose a predictive model for the flow stress of TiAl alloys under different conditions.

TiB crystal whiskers (TiB_w) can be synthesized in situ in Ti alloy matrix through powder metallurgy for the preparation of a new type of ceramic fiber-reinforced Ti matrix composite (TMC) TiB_w/Ti-6Al-4V. In the TiB_w/Ti-6Al-4V TMC, the reinforced phase/matrix interface is clean and has superior comprehensive mechanical properties, but its machinability is degraded. Hence, the bonding of reliable materials is important. To further optimize the TiB_w/Ti-6Al-4V brazing technology and determine the relationship between the microstructure and tensile property of the brazed joint, results demonstrate that the elements of brazing filler metal are under sufficient and uniform diffusion, the microstructure is the typical Widmanstätten structure, and fine granular compounds in β phase are observed. The average tensile strength of the brazing specimen is 998 MPa under room temperature, which is 97.3% of that of the base metal. During the high-temperature (400 °C) tensile process, a fracture occurred at the base metal of the highest tensile test specimen with strength reaching 689 MPa, and the tensile fracture involved a combination of intergranular and transgranular modes at both room temperature and 400 °C. The fracture surface has dimples, secondary cracks are generated by the fracture of TiB whiskers, and large holes form when whole TiB whiskers are removed. The proposed algorithm provides evidence for promoting the application of TiB_w/Ti-6Al-4V TMCs in practical production.

In this paper, spark plasma diffusion bonding technology was employed to join TiAl and Ti₂AlNb with high temperature titanium alloy interlayer at 950 °C/10kN/60 min, then following furnace cooling at cooling rate up to 100 °C/min. After welding, the joint was aging heat-treated at 800 °C for 24 h. The microstructure and the elements diffusion of the TiAl/Ti₂AlNb joint was analyzed by field emission scanning electron microscopy (FESEM) with EDS. Moreover, the tensile properties of the joint were tested at room temperature, 650 °C, and 750 °C. The results show that the spark plasma diffusion bonding formed a high quality TiAl/Ti₂AlNb joint without microcracks or microvoids, while also effectively protecting the base metal. Significant differences in the microstructure of the joint appeared from TiAl side to Ti₂AlNb side: TiAl BM (Base Metal) → DP(Duplex) and NG (Near-Gamma) → α₂-phase matrix with needle-like α-phase → bulk α₂-phase → needle-like α-phase → metastable β-phase → Ti₂AlNb BM. After heat treatment at 800 °C for 24 h, the microstructure of the TiAl side and the interlayer region did not change, but the density and size of the needle-like α-phase in region 3 increased slightly. The microstructure of Ti₂AlNb near the weld changed obviously, and a large number of fine O phases are precipitated from the metastable β phase matrix after heat treatment. Except for the Ti₂AlN near-interface region, the effect of heat treatment on the microstructure of the joint is not significant. The microhardness of the joint is in the shape of a mountain peak. The maximum microhardness at the interface is above 500 HV, and it is significantly reduced to 400 HV after heat treatment. The fracture of the joint occurred at the interface at room temperature, 650 °C, and 750 °C. with the tensile strength 450 MPa, 540 MPa, and 471 Mpa, respectively, and mainly showing brittle fracture.