The organic contamination damage of large-aperture optical components limits laser energy improvement of inertial confinement fusion (ICF). In situ cleaning of large-aperture optical components via low-pressure plasma is expected to remove organic contaminants from the optical surface. Herein, low-pressure air plasma equipment was proposed and used on surfaces of SiO₂ sol–gel antireflection (AR) films in situ by conducting experiments. Its electrical discharge parameters were investigated and optimized during plasma cleaning. Plasma diffusion characteristics and homogeneity in large-aperture windows were analyzed by optical emission spectroscopy. Dramatic degradation in the optical properties of components was observed after organic contamination for 5 h. Transmittance, laser-induced damage threshold and surface morphology observation results demonstrated that low-pressure air plasma removed the organic contaminants from the surface of sol–gel AR films without causing damage and metal contamination. After plasma cleaning, the hydrophilicity of the films increased significantly due to the increase in the polar components of surface free energy. The mechanism of plasma cleaning organic contaminants was confirmed by x-ray photoelectron spectroscopy measurements. These salient results provide a new alternative method for removing organic contaminants in situ from large-aperture optical components and a foundation for improving the energy output of the ICF system.

Orifice-restricted hydrostatic thrust bearings are broadly employed in ultra-precision machine tools, aerospace industries, and so forth. The orifice length–diameter ratio (OLDR) is one of the significant geometrical parameters of the orifice-restricted hydrostatic thrust bearing, which directly affects the performance of the bearing. To accurately guide the design of the hydrostatic thrust bearing, the effect of the OLDR on the performance of the hydrostatic thrust bearing needs to be thoroughly and scientifically investigated, especially for ultra-precision machine tools. In this paper, the influences of various OLDRs are comprehensively studied using the computational fluid dynamics (CFD) approach on the pressure pattern, velocity, turbulent intensity, and vortices, as well as the load capacity, stiffness, volume flow rate, and orifice flow resistance of the hydrostatic thrust bearing under identical operating conditions. The obtained results show that there are differences in performance behaviors of the hydrostatic thrust bearing caused by different OLDRs. Some new findings are obtained, particularly in the second-order small vortices which appear in the annular recesses with all OLDRs except that of 2, and the flow resistance does not always increase with increasing OLDRs. Finally, the proposed CFD approach is experimentally validated.

Process parameters have a significant impact on the filament diameter of extrusion 3D printing. To precisely control filament diameter, this paper proposes a novel method based on experiments to guide process parameter design. Additionally, an extrusion 3D printing device was developed, by which the influence of crucial process parameters and rheological properties on the diameter of printed filaments could be investigated experimentally and theoretically. Furthermore, poly (l-lactide-co-ε-caprolactone) (PLCL) was used as a case study to detail the design procedure of the proposed method. The printable range of the process parameters for PLCL was acquired, and a fitting surface for the experimental data was calculated to guide the process parameter design. According to the results of the experiment, by adjusting the process parameters, PLCL filaments with five different diameters of 120, 130, 140, 150, and 160 μm can be fabricated with a 100 μm nozzle. The deviations between the actual filament diameters and the desired diameter are less than 5 μm, which validates the reliability of the proposed method.

For the extrusion 3D printing process, the printing temperature has a significant impact on the filament formation process because the rheological properties of the printed materials are extremely thermal sensitive, which requires a high temperature control accuracy of the print head. This paper presents a numerical and experimental investigation on the temperature field of a homemade print head. A finite element simulation model for analyzing the temperature field of the print head was established, by which the temperature distribution inside the print head can be acquired. Moreover, to improve the temperature control accuracy, an improved configuration was proposed, and two schemes were compared. The temperature control error dropped from 28% to 6.2% with the improved print head, which was verified experimentally. Furthermore, printing trials were conducted by the optimized print head. The filament diameter could be regulated by changing the temperature of the print head, which validates the feasibility to control the filament diameter during the extrusion process via temperature regulation.

The aerostatic spindle is made up of the structure components and the fluid film. The interaction between them has important influence on the comprehensive performance of the spindle. This paper presents a new design method of aerostatic spindle based on the fluid–structure interaction method. The changes of bearing clearance caused by the structure deformation under high-pressure fluid film are considered, and the static performances of the bearing are obtained. In order to improve the performance of the spindle, the structural parameters of the bearing are optimized. The proposed design method is implemented through a self-developed aerostatic spindle.