This paper presents a comparative study on chitosan degradation in organic acid solutions according to their different dissociation characteristics. More precisely, the aim of the study was to determine the kinetics of the degradation process depending on the different acid dissociation constants (pKa values). The scientists involved in chitosan to date have focused mainly on acetic acid solutions. Solutions of lactic, acetic, malic, and formic acids in concentrations of 3% wt. were used in this research. The progress of degradation was determined based on the intrinsic viscosity measurement, GPC/SEC chromatographic analysis, and their correlation. Changes in the viscosity parameters were performed at a temperature of 20 °C ± 1 °C and a timeframe of up to 168 h (7 days). The chemical structure and DDA of the initial chitosan were analyzed using 1H-NMR spectroscopy analysis. The results of this study can be considered of high importance for the purpose of electrospinning, production of micro- and nano-capsules for drug delivery, and other types of processing. Understanding the influence of the dissociation constant of the solvent on the kinetics of chitosan degradation will allow the selection of an appropriate medium, ensuring an effective and stable spinning process, in which the occurrence of polymer degradation is unfavorable.

One of the biggest economic and environmental sustainability problems is the over-reliance on petroleum chemicals in polymer production. This paper presents an overview of the current state of knowledge on biopolymers combined with biosensors in terms of properties, compounding methods and applications, with a focus on medical and environmental aspects. Therefore, this article is devoted to environmentally friendly polymer materials. The paper presents an overview of the current state of knowledge on biopolymers combined with biosensors in terms of properties, compounding methods and applications, with a special focus on medical and environmental aspects. The paper presents the current state of knowledge, as well as prospects. The article shows that biopolymers made from renewable raw materials are of great interest in various fields of science and industry. These materials not only replace existing polymers in many applications, but also provide new combinations of properties for new applications. Composite materials based on biopolymers are considered superior to traditional non-biodegradable materials due to their ability to degrade when exposed to environmental factors. The paper highlights the combination of polymers with nanomaterials which allows the preparation of chemical sensors, thus enabling their use in environmental or medical applications due to their biocompatibility and sensitivity. This review focuses on analyzing the state of research in the field of biopolymer-sensor composites.

Plastic products, especially in the packaging industry, have become the main commodities penetrating virtually every aspect of our lives. Unfortunately, their omnipresence is not neutral to the natural environment. Pollution in the form of microplastics is a global problem. Therefore, green technologies that enter into the circular economy become an important topic. As part of the research work, the modification of poly(lactic acid) has been studied for use in the packaging industry. Due to its intrinsic rigidity, plasticizing substances had to be introduced in PLA in order to improve its plastic deformability. Both high-molecular compounds such as ethoxylated lauryl alcohol, block copolymer of ethylene oxide and propylene oxide, and ethoxylated stearic acid as well as low-molecular compounds such as di-2-ethylhexyl adipate, di-2-ethylhexyl sebacate, and triethyl citrate were used. The samples extruded from plasticized polymers were characterized using differential scanning calorimetry, thermal gravimetric analysis, and mechanical properties including Young’s modulus. The melt flow rate (MFR) and molar mass distribution were determined. For all modified samples the glass transition temperature, depending on the plasticizer used, was shifted towards lower values compared to the base polymer. The best result was obtained for di-2-ethylhexyl adipate (ADO) and di-2-ethylhexyl sebacate (SDO). The elongation at break increased significantly for ADO at about 21%. The highest elongation was obtained for SDO (about 35%), although it obtained a higher glass temperature. The degradation of the polymer was not observed for both plasticizers. For these plasticizers (ADO and SDO) it also lowered Young’s module by about 26%, and at the infrared spectrum deformation of peaks were observed, which may indicate the interaction of the ester carbonyl group of PLA with plasticizers. Therefore it can be concluded that they are good modifiers. The selected plasticizers that are used in the production of food contact materials, in particular in the production of PVC (polyvinyl chloride) food films, also exhibited great potential to be applied to PLA food films, and exhibit better properties than the citrate, which are indicated in many publications as PLA plasticizers.

Biopolymer composites have received increasing attention for their beneficial properties such as being biodegradable and having less influence to the environment. Biodegradability of materials has become a desired feature due to the growing problems connected with waste management. The aim of the paper is to emphasize the importance of biodegradable textile materials, especially nonwoven materials with an anti-pathogenic layer. The article refers to the definitions of biodegradation, degradation and composting processes, as well as presenting methods of testing biodegradability depending on the type of material. The study gives examples of biodegradation of textiles and presents examples of qualitative and quantitative methods used for testing antimicrobial activity of biodegradable nonwovens with an anti-pathogenic layer.

In recent years, the amount of produced petrochemical plastic waste has been growing at an alarming rate. According to the Plastics Europe Market Research Group (PEMRG)/Conversio Market & Strategy GmbH, in 2018 the global production of plastics amounts to 359 million tons, and in Europe—61.8 million tons. More than 80% of all marine litter is plastic, which accumulates in the environment due to its durability. Due to the growing problem, biodegradable polymer products are introduced to the market. Therefore, it is necessary to conduct research on degradation products in order to estimate the risk arising from their presence in the environment. This paper discusses research on compounds that may potentially remain in the soil after the degradation of the double green PLA polymer. The aim of the research was to prove whether products made of PLA, e.g., packaging, films and other waste can release substances harmful to the environment. Therefore, soil was selected as a medium to characterize the substances potentially released from the polymer under conditions simulating the degradation process in the environment. The soil was always used from the same producer. Before the polymer biodegradation process, it was additionally checked for pH, C and N content, number of microorganisms, etc. PLA degradation in soil was carried out in a laboratory accredited by the Polish Accreditation Center (PCA). During the research, soil samples at various stages of the degradation process under laboratory conditions were subjected to both extraction in an aqueous environment and organic solvent extraction The studies used the gas chromatography coupled with mass spectrometry (GC/MS), as well as pyrolysis gas chromatography (Py-GC/MS). In addition, the study used the gel permeation chromatography (GPC/SEC) allowing to determine the distribution of molar masses, average molar masses and polydispersity, and the infrared spectroscopy (FTIR).

The COVID-19 pandemic was first reported on 31 December 2019, in Wuhan. Since then, the rapid spread of the virus has directly impacted various aspects of people’s lives, including culture, society, education, and the economy. The environment has also been affected, as the disposal of thousands of tons of single-use personal protective equipment has resulted in a significant increase in waste. The challenge was to create environmentally friendly materials for personal protective equipment. One of the alternatives to polypropylene materials is a biodegradable nonwoven produced using spun-bonded technology. The article discusses various physical and mechanical parameters, the biodegradation process, and the distribution of molar masses during the weeks of nonwoven biodegradation. Additionally, the paper presents the results of in vitro cytotoxicity tests conducted on the material. Biodegradable materials are a viable solution to the challenges posed by a circular economy.