In this work, a highly alloyed cold work tool steel, Uddeholm Vanadis 4 Extra, was manufactured via the electron beam melting (EBM) technique. The corresponding material microstructure and carbide precipitation behavior as well as the microstructural changes after heat treatment were characterized, and key mechanical properties were investigated. In the as-built condition, the microstructure consists of a discontinuous network of very fine primary Mo- and V-rich carbides dispersed in an auto-tempered martensite matrix together with ≈15% of retained austenite. Adjusted heat treatment procedures allowed optimizing the microstructure by the elimination of Mo-rich carbides and the precipitation of fine and different sized V-rich carbides, along with a decrease in the retained austenite content below 2%. Hardness response, compressive strength, and abrasive wear properties of the EBM-manufactured material are similar or superior to its as-HIP forged counterparts manufactured using traditional powder metallurgy route. In the material as built by EBM, an impact toughness of 16–17 J was achieved. Hot isostatic pressing (HIP) was applied in order to further increase ductility and to investigate its impact upon the microstructure and properties of the material. After HIPing with optimized protocols, the ductility increased over 20 J.
A novel Human Head Surrogate was obtained from available MRI scans of a 50th percentile male human head. Addictive manufacturing was used to produce the skull, the brain and the skin. All original MRI geometries were partially smoothed and adjusted to provide the best biofidelity compatible with printing and molding technology. The skull was 3D-printed in ABS and ten pressure sensors were placed into it. The brain surrogate was cast from silicon rubber in the 3D-printed plastic molds. Nine tri-axial accelerometers (placed at the tops of the lobes, at the sides of the lobes, in the cerebellum and in the center of mass) and a three-axis gyroscope (at the center of mass) were inserted into the silicon brain during casting. The cranium, after assembly with brain, was filled with silicon oil mimicking the cerebral fluid. Silicon rubber was cast in additional 3D-printed molds to form the skin surrounding the cranium. The skull base was adapted to be compatible with the Hybrid-III neck and allow the exit of brain sensors cabling. Preliminary experiments were carried out proving the functionality of the surrogate. Results showed how multiple accelerometers and pressure sensors allowed a better comprehension of the head complex motion during impacts.
Phenomena of the ski and snow boards vibrations generated in gliding are known for years. In the cross country and jumping skis such vibrations are not very obvious but can play quite positive role reducing the effective gliding friction. The research into the nature of friction-induced vibrations and the factors influencing their frequencies and magnitudes is driven by the desire to control them for improving ski gliding performance. Significant amount of experimental data acquired in the field and laboratory studies is already available making it possible to formulate certain qualitative conclusions. But so far it did not bring comprehensive understanding of the phenomenon and specifically of the mechanisms controlling such vibrations. Modeling is one of the potent tools allowing to deeper understand experimentally studied phenomena and it can provide much stronger quantitative prediction capacity. Present paper discusses possible approaches to modeling of the phenomenon and first results of constructing simplified models
Global textile production and consumption has increased steadily over the past 15 years, which has caused significant impacts on the climate and the environment. In 2022, the EU launched a strategy for sustainable and circular textiles, stating that extending the life of textile products is the most efficient way to reduce their impact on the climate and the environment. Shell jackets for outdoor use are textile products that are frequently discarded by their first users and re-sold on the second-hand market. This study evaluates the performance of 16 second-hand shell jackets from three second-hand stores in Sweden via material testing of four key functional aspects. Comparing the results with the jackets’ original performance, this study describes the change in functionality over time. The results indicate that air permeability does not change significantly, whereas water repellency, water penetration resistance, and breathability decrease over time, although they do so at different rates. With the aim of promoting circularity and encouraging longer product use, this study also compares the price evolution of jackets with their functionality over time. The results reveal that the resale price of the jackets is lower than could be expected based on the level of remaining functionality in the jackets.
The wind tunnel at the SportsTech Research Centre at Mid Sweden University (MIUN, Ostersund) was opened in 2015 for sports technology research. It is dedicated to analysis of equipment performance and garment development and suitable for roller skiing, running and cycling. The aim of this work was to develop and apply a full-scale method to investigate the aerodynamic behaviour of a cyclist facing front and cross wind at different yaw angles (from 0° to 30°) and speeds. To reach this goal, a rotating structure supported by a force platform was constructed. It includes a set of rollers on which fully unrestrained cycling is possible. The method was applied to the comparison of three wheelsets (differing in material, height and shape of the rim, number and shape of spokes) in terms of drag and side aerodynamic forces during a cyclist’s ride at 30 km/h, while keeping all the other factors constant. Resulting curves allowed estimating differences of 4% and 9% when applied to a recent time trial competition with supposed wind conditions.