In this paper, a gravity-triggered liquid metal microstrip patch antenna with reconfigurable frequency is proposed with experimental verification. In this work, the substrate of the antenna is quickly obtained through three-dimensional (3D) printing technology. Non-toxic EGaIn alloy is filled into the resin substrate as a radiation patch, and the NaOH solution is used to remove the oxide film of EGaIn. In this configuration, the liquid metal inside the antenna can be flexibly flowed and deformed with different rotation angles due to the gravity to realize different working states. To validate the conception, the reflection coefficients and radiation patterns of the prototyped antenna are then measured, from which it can be observed that the measured results closely follow the simulations. The antenna can obtain a wide operating bandwidth of 3.69–4.95 GHz, which coverage over a range of frequencies suitable for various channels of the 5th generation (5G) mobile networks. The principle of gravitational driving can be applied to the design of reconfigurable antennas for other types of liquid metals.

A one-step strategy for fabricating flexible conductors via phase separation is proposed, wherein, the liquid metal was implanted into polydimethylsiloxane, whose viscosity was changed using hexane. Such self-encapsulating composite exhibited good electronic and mechanical stability under mechanical cycles with no significant leaking of droplets during the testing process.

This communication provides an integrated process route of smelting gallium-based liquid metal (GBLM) in a high vacuum, and injecting GBLM into the antenna channel in high-pressure protective gas, which avoids the oxidation of GBLM during smelting and filling. Then, a frequency-reconfigurable antenna, utilizing the thermal expansion characteristic of GBLM, is proposed. To drive GBLM into an air-proof space, the thermal expansion characteristics of GBLM are required. The dimensions of the radiating element of the liquid metal antenna can be adjusted at different temperatures, resulting in the reconfigurability of the operating frequency. To validate the proposed concept, an L-band antenna prototype was fabricated and measured. Experimental results demonstrate that the GBLM in the antenna was well filled, and the GBLM was not oxidized. Due to the GBLM being in an air-proof channel, the designed liquid metal antenna without electrolytes could be used in an air environment for a long time. The antenna is able to achieve an effective bandwidth of over 1.25–2.00 GHz between 25 °C and 100 °C. The maximum radiation efficiency and gain in the tunable range are 94% and 2.9 dBi, respectively. The designed antenna also provides a new approach to the fabrication of a temperature sensor that detects temperature in some situations that are challenging for conventional temperature sensing technology.

Room temperature liquid metal (LM) showcases a great promise in the fields of flexible functional thin film due to its favorable characteristics of flexibility, inherent conductivity, and printability. Current fabrication strategies of liquid metal film are substrate structure specific and sustain from unanticipated smearing effects. Herein, this paper reported a facile fabrication of liquid metal composite film via sequentially regulating oxidation to change the adhesion characteristics, targeting the ability of electrical connection and electrothermal conversion. The composite film was then made of the electrically resistive layer (oxidizing liquid metal) and the insulating Polyimide film (PI film) substrate, which has the advantages of electrical insulation and ultra-wide temperature working range, and its thickness is only 50 μm. The electrical resistance of composite film can maintain constant for 6 h and could work normally. Additionally, the heating film exhibited excellent thermal switching characteristics that can reach temperature equilibrium within 100 s, and recovery to ambient temperature within 50 s. The maximum working temperature of the as-prepared film is 115 °C, which is consistent with the result of the theoretical calculation, demonstrating a good electrothermal conversion capability. Finally, the heating application under extreme low temperature (−196 °C) was achieved. This conceptual study showed the promising value of the prototype strategy to the specific application areas such as the field of smart homes, flexible electronics, wearable thermal management, and high-performance heating systems.

This study presents a U-shaped dual-frequency-reconfigurable liquid-metal monopole antenna. Eutectic Gallium–Indium (EGaIn) was used as a conductive fluid and filled in the two branches of the U-shaped glass tube. A precision syringe pump was connected to one of the branches of the U-shaped tube by a silicone tube to drive EGaIn, forming a height difference between the two liquid levels. When the height of liquid metal in the two branches met the initial condition of L₁ = L₂ = 10 mm, and L₁ increased from 10 mm to 18 mm, the two branches obtained two working bandwidths of 2.27–4.98 GHz and 2.71–8.58 GHz, respectively. The maximum peak gain was 4.00 dBi. The initial amount of EGaIn also affected the available operating bandwidth. When the liquid metal was perfused according to the initial condition: L₁ = L₂ = 12 mm, and L₁ was adjusted within the range of 12–20 mm, the two branches had the corresponding working bandwidths of 2.18–4.32 GHz and 2.57–9.09 GHz, and the measured maximum peak gain was 3.72 dBi. The simulation and measurement data corresponded well. A series of dual-frequency-reconfigurable antennas can be obtained by changing the initial amount of EGaIn. This series of antennas may have broad application prospects in fields such as base stations and navigation.

This paper proposes a method for pressure driven rapid reconfigurable liquid metal patterning. A sandwich structure of “pattern—film—cavity” is designed to complete this function. Both sides of the highly elastic polymer film are bonded with two PDMS slabs. One PDMS slab has microchannels patterned on the surface. The other PDMS slab has a large cavity on its surface for liquid metal storage. These two PDMS slabs are bonded together, face to face, with the polymer film in the middle. In order to control the distribution of the liquid metal in the microfluidic chip, the elastic film will deform under the high pressure of the working medium in the microchannels and then extrude the liquid metal into different patterns in the cavity. This paper studies the factors of liquid metal patterning in detail, including external control conditions, such as the type and pressure of the working medium and the critical dimensions of the chip structure. Moreover, both a single-pattern and a double-pattern chip are fabricated in this paper, which can form or reconfigure the liquid metal pattern within 800 ms. Based on the above methods, reconfigurable antennas of two frequencies are designed and fabricated. Meanwhile, their performance is simulated and tested by simulation and vector network tests. The operating frequencies of the two antennas are respectively significantly switching between 4.66 GHz and 9.97 GHz.