The broader use of cements with a higher content of the main non-clinker components in construction industry is one of the directions leading to the decarbonization in cement production. This contribution analyzes the properties of low-emission cements containing from 44% to 56% of Portland clinker in their composition and indicates the possibilities of wider use in the construction. The obtained results confirmed that following the appropriate technological regimes, low-emission cements can be implemented into the production of concrete exposed to carbonation-induced corrosion (exposure class XC4 according to EN 206), frost-resistant concrete (exposure class XF4 according to EN 206), self-compacting concrete (SCC) and high-performance concrete (HPC). An analysis of the level of CO2 emissions in the production of specific types of concrete using low-emission cements was also made.
The current work presents the complex investigation of the influence of cement and aggregate type on the thermo-mechanical behavior of mass concrete. Six types of cement with different amounts of non-clinker constituents and four types of aggregates are used in experimental tests. Particular attention was given to the low clinker cements with high amounts of siliceous fly ash and ground blast furnace slag. The experimental research covered the determination of thermal, mechanical, and rheological properties of early age concrete with different constituents. Experimental results have been used both to validate the numerical model and analysis of exemplary foundation slab. The results confirm the importance of the concrete mix composition and it has been shown that the early-age volume deformation and possible cracking is the result of the concerted action of thermal and mechanical properties of concrete. The obtained results indicate granite as the best aggregate for mass concrete. Considering the type of cement, much better behaviour of mass concrete has been noted for cements with fly ash and composite cements containing both fly ash and slags than cements only with slag.
The paper presents the composition and properties of low-emission ternary cements: Portland multicomponent cement CEM II/C-M and multicomponent cement CEM VI. In the ternary cements, Portland clinker was replaced at the levels of 40% and 55% with a mixture of the main components such as limestone (LL), granulated blast furnace slag (S) and siliceous fly ash (V). Portland multicomponent cements CEM II/C-M and CEM VI are low-emission binders with CO2 emissions ranging from 340 (CEM VI) kg to 453 (CEM II/C-M) kg per Mg of cement. The results obtained indicate the possibility of a wider use of ground limestone (LL) in cement composition. This is important in the case of limited market availability of fly ash and granulated blast furnace slag. The tests conducted on concrete have shown that the necessary condition for obtaining a high strength class and durability of concrete from CEM II/C-M and CEM VI ternary cements is low water–cement ratio. Durability characteristics of concrete (carbonation susceptibility, chloride ion permeation, frost resistance) made of CEM II/C-M and CEM VI cements were determined after 90 days of hardening. This period of curing reflects the performance properties of the concrete in a more effective way.
This paper presents the results of research on the influence of polymer modifiers: styrene-acrylic copolymer, vinyl acetate/ethylene (EVA), vinyl acetate/acrylic copolymer (VAAc), and VA/VeoVa/acrylic terpolymer on the water permeability and adhesion of cement-containing waterproofing mortars in concrete. The content of the polymers in the composition of the mortars was 15, 20 and 26% (m/m) in relation to the weight of the dry ingredients. Using microscopic methods, an attempt was made to analyse the relationship between the microstructure of the mortars and the properties of these polymers. The EVA and the vinyl acetate/acrylic copolymer, which were used in the form of dry powders, had the most favourable effect on water permeability and adhesion to the concrete substrate. They may prove to be useful for the production of one-component cement-containing waterproofing mortars. On the other hand, the VA/VeoVa/acrylic terpolymer modifier had the least favourable effect on the tested properties. For mortars with this modifier, the desired water-permeability parameters were not achieved. Depending on the amount of polymer modifier, the mortars were characterized by differences in watertightness, as established on the basis of changes in porosity and differences in the adhesion of the cement-polymer paste to the surface of aggregate grains. It was determined that the type of polymer and its dispergation properties influence the water permeability of mortars, as well as their adhesion to concrete substrates.
It is currently vital to use more environmentally friendly cementitious composites, such as blended slag-limestone cements. However, many properties of slag-limestone cements are not yet fully research, especially in regards to the effect of limestone properties on properties of mortars and concrete. In the research, three types of slag cements were mixed with two types of limestone to obtain multi-component slag-limestone cements. Tests of rheological properties, heat of hydration, and compressive strength were conducted to ascertain the effect of limestone on the cement properties and to check the viability of this type of cement for engineering practice. It was found that the addition of up to 10% of limestone to slag cements did not have negative effects on tested properties; however, the exact influence of limestone was dependent on limestone particle size distribution. Increasing the amount of limestone in limestone-slag cements to 15% significantly decreased the compressive strength of the mortars and decreased hydration heat but had no significant effect on rheological properties.
1 February 2014 in Roads and Bridges – Drogi i Mosty
Usefulness of domestic calcareous fly ashes as pozzolanic and hydraulic constituents of cements and hydraulic binders is a subject of this paper. Test results of standard properties, activity indices of calcareous fly ashes and physical and mechanical properties of cements with this kind of fly ash are presented. Factors which might exerted an influence on hydration and hardening processes of cements with calcareous fly ashes form Bełchatow Power Station were analyzed. Beneficial results of calcareous fly ash activity were discussed regarding phase composition and morphology. The function of glassy phase in hydration and hardening processes of fly ashes as well as cements and binders with this constituent was emphasized.