Philippe Micheau

Philippe Micheau


Research Focus & Metrics

Academic Career Length

30Years (1997-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 October 2018 in Structural Health Monitoring
Verified
Journal Article
Closed access
VSValentin Serey
Valentin Serey
NQNicolas Quaegebeur
Nicolas Quaegebeur
PMPhilippe Micheau
Philippe Micheau
PMPatrice Masson
Patrice Masson
MCMichel Castaings
Michel Castaings
MRMathieu Renier
Mathieu Renier
Non-destructive testing and structural health monitoring systems based on ultrasonic guided waves propagation are particularly used in civil engineering or aerospace applications. Guided waves are commonly employed as they propagate through large distances and can inspect the entire cross-section of the structure. In order to optimize the sensitivity to a specific damage type, it is often preferable to generate a carefully selected pure mode. Although single-mode generation has been achieved for Lamb waves in infinite plate-like structures, such generation is much harder in a rectangular bar since less conventional modes propagate in finite cross-section waveguides. This article presents a general methodology for mode selective generation in a finite cross-section waveguide, using multiple transducers. Obtaining modal identification through conventional spatial Fourier transform on a longitudinal scan has proven to be inconvenient for waveguides with a two-dimensional cross-section. An alternative technique is proposed, consisting in the decomposition over the modal basis of the three displacement components measured across the bar width at the bar surface. The methodology is applied to the single-mode generation within an aluminum bar instrumented with eight piezoelectric transducers bonded to the surface. The modal basis is obtained with a semi-analytical finite element method. Numerical simulations and experiments using a three-dimensional laser Doppler vibrometer are conducted in order to validate the methodology.

16 August 2020 in Structural Health Monitoring
Verified
Journal Article
Closed access
PDF file
VSValentin Serey
Valentin Serey
NQNicolas Quaegebeur
Nicolas Quaegebeur
MRMathieu Renier
Mathieu Renier
PMPhilippe Micheau
Philippe Micheau
PMPatrice Masson
Patrice Masson
MCMichel Castaings
Michel Castaings
Ultrasonic guided waves are used in non-destructive testing and structural health monitoring solutions for long-range inspection, in applications ranging from Civil Engineering to Aerospace. In order to ease the inspection process, it is generally preferable to generate a carefully selected single mode. Although single mode Lamb wave generation is not difficult to achieve in infinite plate-like structures, with carefully polarized or sized piezoceramic elements, for example, such selective generation is much more difficult in a rectangular bar. In this article, we consider the propagation along a thin plate of finite rectangular cross section, which corresponds to a rectangular bar. The finite lateral width leads to a greater density of modes compared to an infinite plate. The authors have previously addressed this matter and developed a methodology for the selective generation of modes in the harmonic regime. This article extends this methodology to selective mode generation for finite time excitation, such as bursts. Results are presented for single mode generation of A0,0 and A0,1 in an aluminum bar instrumented with eight piezoelectric transducers. The waveguide modal basis is calculated with the two-dimensional semi-analytical finite element method, and measurements are conducted using a three-dimensional laser-Doppler vibrometer. To illustrate the potential of the method for structural health monitoring purposes, the detection of a defect simulated by a pair of magnets placed at various positions over the bar width is demonstrated.

1 May 2009 in The Journal of the Acoustical Society of America
Verified
Journal Article
Closed access
NQNicolas Quaegebeur
Nicolas Quaegebeur
PMPhilippe Micheau
Philippe Micheau
ABAlain Berry
Alain Berry
The problem under study in this article is the active control of sound transmission and radiation of a panel under a periodic excitation. The control strategy investigated uses independent control loops between an individual polyvinylidene fluoride (PVDF) sensor and an individual lead zirconate titanate (PZT) actuator. The specific approach employed here uses the concept of virtual impedance. The aim is to determine for each frequency the optimal impedance between each PVDF sensor and the corresponding PZT actuator in order to reduce the sound power radiated by the plate. Theoretical predictions are compared to measurements of the sound radiated and transmission loss of a panel mounted with eight PZT-PVDF units. Reductions of up to 20 dB of the acoustic power can be achieved around mechanical resonances of the system, while the control strategy has little effect for off-resonance excitations.

21 May 2012 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
Verified
Journal Article
Closed access
NQNicolas Quaegebeur
Nicolas Quaegebeur
PMPatrice Masson
Patrice Masson
PMPhilippe Micheau
Philippe Micheau
NMNezih Mrad
Nezih Mrad
Classically, damage detection or dispersion curve determination using piezoceramic-generated guided waves has been based on analysis of propagation properties of multiple narrowband excitation signals. However, dispersion and multimodal propagation impair the determination of propagation properties. More recently, it has been proposed to consider broadband excitations for both damage imaging and group velocity estimation. Among existing transducer technologies, although laser excitation is prone to practical limitations in terms of dimensions and generated amplitudes, it allows generation of noncontact, point-like broadband displacement. Thus, broadband generation of guided waves using piezoceramics can be envisioned. However, direct impulse response measurements are limited by the generated amplitude, leading to low SNR measurements. For this purpose, chirp excitations have been proposed using variable-frequency bursts, leading to phase and amplitude variations with respect to the frequency, such that this approach is not suitable for precise estimation of time of flight (ToF) or modal amplitude. In this paper, a sub-band decomposition technique that allows high-SNR measurements of impulse response in a given frequency range is proposed. Broadband excitation is decomposed over a given number of frequency sub-bands, generated by a piezoceramic element and measurement is performed using a laser Doppler vibrometer (LDV) or a piezoceramic sensor. Application to experimental estimation of group velocity and damage detection in pitchcatch configuration is proposed. It is shown that the proposed method allows damage estimation without a priori knowledge of the damage size, whereas narrowband techniques can fail at specific wavelengths.

28 May 2019 in IEEE/ASME Transactions on Mechatronics
Verified
Journal Article
Closed access
RTRobin Temporelli
Robin Temporelli
MBMaxime Boisvert
Maxime Boisvert
PMPhilippe Micheau
Philippe Micheau
The powertrain performance and comfort of a vehicle are largely dependent on the clutch control strategy for Automated Manual Transmission (AMT). In most industrial cases, clutch control is managed by clutch pressure control irrespective of clutch actuation technology. However, clutch pressure control represents a challenge with regard to clutch non-linearities and time-varying parameters (especially with electromechanical technology). In this paper, the electrohydraulic TMA of a three-wheeled motorcycle is considered. In the context of replacing its electrohydraulic clutch actuator (EHA) by a new electromechanical clutch actuator (EMA) for fuel savings, a Dual Sliding Mode Controller (DSMC) is proposed in order to control clutch pressure with the EMA. The clutch and its EMA are modeled through an analytical model including two non-linear components. The EMA was prototyped and subsequently enclosed in an environmental chamber. Experimental investigations revealed both predicted non-linearities in the system and allowed identifying several numeric models of the system's dynamics. In keeping with these experimental investigations, the DSMC architecture and algorithm was developed, in which the robustness of the DSMC was proven through a Lyapunov analysis and the original use of the bang-bang component enabled to overcome static friction without introducing chattering. Lastly, the test bench setup was used to experimentally highlight controller robustness and performance. Finally, the better control performance and accuracy of the EMA and its DSMC over the current integrated EHA and its associated PI controller were pointed out with respect to four critical clutch operational cases.