In this paper, a rigorous procedure for the circuit-level analysis and design of entire systems, developed to provide power wirelessly, is presented. A unified theoretical approach is first introduced, based on a two-port-equivalent circuit representation, to describe the wireless power transfer link when the transmitter and the receiver are either in the near-field or in the far-field region reciprocally. This approach allows one to compute in a straightforward manner the system figure of merit, namely the power transfer efficiency. Specific guidelines for the two configurations are then intensively discussed together with the adopted software tools based on the combination of full-wave analysis and nonlinear harmonic balance techniques. Several practical examples based on this design procedure are presented, demonstrating predicted and experimental behavior of unconventional devices for both near-field and far-field power transfer usage.

This paper describes the design and realization of a magnetic indoor positioning system. The system is entirely realized using off-the-shelf components and is based on inductive coupling between resonating coils. Both system-level architecture and realization details are described along with experimental results. The realized system exhibits a maximum positioning error of <;10 cm in an indoor environment over a 3 × 3 m ² area. Extensive experiments in larger areas, in nonline-of-sight conditions, and in unfavorable geometric configurations, show submeter accuracy, thus validating the robustness of the system with respect to other existing solutions.

This paper describes the design and the realization of a low-frequency ac magnetic-field-based indoor positioning system (PS). The system operation is based on the principle of inductive coupling between wire loop antennas. Specifically, due to the characteristics of the ac artificially generated magnetic fields, the relation between the induced voltage and the distance is modeled with a linear behavior in a bilogarithmic scale when a configuration with coplanar, thus equally oriented, antennas is used. In this case, the distance between a transmitting antenna and a receiving one is estimated using measurements of the induced voltage in the latter. For a high operational range, the system makes use of resonant antennas tuned at the same nominal resonant frequency. The quality factors act as antenna gain increasing the amplitude of the induced voltage. The low-operating frequency is the key factor for improving robustness against nonline-of-sight (NLOS) conditions and environment influences with respect to other existing solutions. The realized prototype, which is implemented using off-the-shelf components, exhibits an average and maximum positioning error, respectively, lower than 0.3 and 0.9 m in an indoor environment over a large area of 15 m × 12 m in NLOS conditions. Similar performance is obtained in an outdoor environment over an area of 30 m × 14 m. Furthermore, the system does not require any type of synchronization between the nodes and can accommodate an arbitrary number of users without additional infrastructure.

This paper describes the design and realization of a 5.6-GHz ultrawide-bandwidth-based position measurement system. The system was entirely made using off-the-shelf components and achieves centimeter-level accuracy in an indoor environment. It is based on asynchronous modulated pulse round-trip time measurements. Both system level and realization details are described along with experimental results including estimates of measurement uncertainties.

This letter presents a simple and cheap metal-plating procedure for plastic 3-D printed microwave components. The devices are built using a Stereolithographic printer and then metalized by a two-step process consisting in a silver-painted substrate followed by copper electrodeposition. The method achieves good adhesion of the metal to the plastic body and high conductivity. Resonators and X -band filters have been fabricated and tested, showing excellent performance in terms of dimensional accuracy and low loss, with quality factors better than 6500. The technique can be usefully employed for fast and cheap prototyping of microwave components at least up to the X -band.

The proposed approach makes use of full-wave electromagnetic modeling of wireless power transfer links in order to derive the network characterization, e.g., in terms of scattering or impedance matrix. Once the latter is obtained, we show that network theory provides the appropriate matching impedances for achieving either maximum efficiency, maximum power on the load, or conjugate matching. The proposed approach also permits to derive closed-form matching networks and expressions for power and efficiency. An example of full-wave numerical electromagnetic modeling of a wireless power transfer link is presented. The selected example, which is similar to the experiment published by Kurs et al., shows the importance of selecting the appropriate source/load impedance for obtaining significative results.