In recent years, autonomous vehicles and advanced driver assistance systems have drawn a great deal of attention from both research and industry, because of their demonstrated benefit in reducing the rate of accidents or, at least, their severity. The main flaw of this system is related to the poor performances in adverse environmental conditions, due to the reduction of friction, which is mainly related to the state of the road. In this paper, a new model-based technique is proposed for real-time road friction estimation in different environmental conditions. The proposed technique is based on both bicycle model to evaluate the state of the vehicle and a tire Magic Formula model based on a slip-slope approach to evaluate the potential friction. The results, in terms of the maximum achievable grip value, have been involved in autonomous driving vehicle-following maneuvers, as well as the operating condition of the vehicle at which such grip value can be reached. The effectiveness of the proposed approach is disclosed via an extensive numerical analysis covering a wide range of environmental, traffic, and vehicle kinematic conditions. Results confirm the ability of the approach to properly automatically adapting the inter-vehicle space gap and to avoiding collisions also in adverse road conditions (e.g., ice, heavy rain).

Vehicle dynamics control systems have a fundamental role in smart and autonomous mobility, where one of the most crucial aspects is the vehicle body velocity estimation. In this paper, the problem of a correct evaluation of the vehicle longitudinal velocity for dynamic control applications is approached using a neural networks technique employing a set of measured samples referring to signals usually available on-board, such as longitudinal and lateral acceleration, steering angle, yaw rate and linear wheel speed. Experiments were run on four professional driving circuits with very different characteristics, and the vehicle longitudinal velocity was estimated with different neural network training policies and validated through comparison with the measurements of the one acquired at the vehicle’s center of gravity, provided by an optical Correvit sensor, which serves as the reference (and, therefore, exact) velocity values. The results obtained with the proposed methodology are in good agreement with the reference values in almost all tested conditions, covering both the linear and the nonlinear behavior of the car, proving that artificial neural networks can be efficiently employed onboard, thereby enriching the standard set of control and safety-related electronics.

In recent years the increasing needs of reducing the costs of car development expressed by the automotive market have determined a rapid development of virtual driver prototyping tools that aims at reproducing vehicle behaviors. Nevertheless, these advanced tools are still not designed to exploit the entire vehicle dynamics potential, preferring to assure the minimum requirements in the worst possible operating conditions instead. Furthermore, their calibration is typically performed in a pre-defined strict range of operating conditions, established by specific regulations or OEM routines. For this reason, their performance can considerably decrease in particularly crucial safetycritical situations, where the environmental conditions (rain, snow, ice), the road singularities (oil stains, puddles, holes), and the tyre thermal and ageing phenomena can deeply affect the adherence potential. The objective of the work is to investigate the possibility of the physical model-based control to take into account the variations in terms of the dynamic behavior of the systems and of the boundary conditions. Different scenarios with specific tyre thermal and wear conditions have been tested on diverse road surfaces validating the designed model predictive control algorithm in a hardware-in-the-loop real-time environment and demonstrating the augmented reliability of an advanced virtual driver aware of available information concerning the tyre dynamic limits. The multidisciplinary proposal will provide a paradigm shift in the development of strategies and a solid breakthrough towards enhanced development of the driving automatization systems, unleashing the potential of physical modeling to the next level of vehicle control, able to exploit and to take into account the multi-physical tyre variations.

Vehicle dynamics can be deeply affected by various tyre operating conditions, including thermodynamic and wear effects. Indeed, tyre temperature plays a fundamental role in high performance applications due to the dependencies of the cornering stiffness and potential grip in such conditions. This work is focused on the evaluation of a potentially improved control strategy’s performance when the control model is fed by instantaneously varying tyre parameters, taking into account the continuously evolving external surface temperature and the vehicle boundary conditions. To this end, a simplified tyre thermal model has been integrated into a model predictive control strategy in order to exploit the thermal dynamics’ dependents within a proposed advanced ABS control system. We evaluate its performance in terms of the resulting braking distance. In particular, a non-linear model predictive control (NMPC) based ABS controller with tyre thermal knowledge has been integrated. The chosen topic can possibly lay a foundation for future research into autonomous control where the detailing of decision-making of the controllers will reach the level of multi-physical phenomena concerning the tyre–road interaction.

The understanding of tire’s adherence with a rough surface is a common goal for several fields in the automotive sector. In fact, grip is synonym of safety and performance, playing a decisive role for braking distance and vehicle stability, fuel consumption, wear rate [1], noise generation and for the vehicle dynamics control system (e.g. ABS, TCS, AYC and other) [2]. This paper deals with tire tread grip experimental investigation and evaluation under different conditions that influence it during the sliding contact [3]. In this regard the test campaign involves the use of different tire compounds (in terms of viscoelastic characteristics), tested in several conditions: different contact pressure, sliding speed, temperature, sliding contact length and road surface. The test bench employed by the UniNa Vehicle Dynamic Research Group is an upgrade of the British Pendulum, an instrument for outdoor tribological tests on road sections. The principal sensors installed on the test bench are an encoder, for the evaluation of the sliding speed of the tire specimen, and a load cell, for the measurement of the force arising at tire/road interface in the longitudinal and vertical directions [4]. In fact, the grip shall be determined as the ratio of the longitudinal force and corresponding load on the tire. The paper's aim is the description of the experimental campaign after an accurate introduction on the test setup and an illustration of the equipment. Finally, the preliminary results and the methodologies used to process the acquired data are described.