One-step reactive melt processing (REx) via radical reactions was evaluated with the aim of improving the rheological properties of poly(ε-caprolactone) (PCL). In particular, a water-assisted REx was designed under the hypothesis of increasing crosslinking efficiency with water as a low viscous medium in comparison with a slower PCL macroradicals diffusion in the melt state. To assess the effect of dry vs. water-assisted REx on PCL, its structural, thermo-mechanical and rheological properties were investigated. Water-assisted REx resulted in increased PCL gel fraction compared to dry REx (from 1–34%), proving the rationale under the formulated hypothesis. From dynamic mechanical analysis and tensile tests, the crosslink did not significantly affect the PCL mechanical performance. Dynamic rheological measurements showed that higher PCL viscosity was reached with increasing branching/crosslinking and the typical PCL Newtonian behavior was shifting towards a progressively more pronounced shear thinning. A complete transition from viscous- to solid-like PCL melt behavior was recorded, demonstrating that higher melt elasticity can be obtained as a function of gel content by controlled REx. Improvement in rheological properties offers the possibility of broadening PCL melt processability without hindering its recycling by melt processing.
23 December 2024 in ACS Applied Materials & Interfaces
The full exploitation of the outstanding mechanical properties of cellulose nanofibrils (CNFs) as potential reinforcements in nanocomposite materials is limited by the poor interactions at the CNF-polymer matrix interface. Within this work, tailor-made copolymers were designed to mediate the interface between CNFs and biodegradable poly(butylene adipate-co-terephthalate) (PBAT), and their effect on extruded nanocomposite performance was tested. For this purpose, two well-defined amphiphilic anchor-tail diblock copolymer structures were compared, with a fixed anchor block length and a large difference in the hydrophobic tail block length. The aim was to evaluate the impact of the copolymers' chain length on the nanocomposite interface. The presence of amphiphilic diblock copolymers significantly improved the mechanical properties compared to those of PBAT nanocomposites containing unmodified CNFs. In particular, the copolymer with a longer tail was more effective for CNF-PBAT dispersion interactions, leading to a 65% increase of Young's modulus of neat PBAT, while retaining high deformability (670%). The results provide insights into the effectiveness of a waterborne third component at the CNF-matrix interface and its structure-property relationship.
4 September 2021 in Journal of Applied Polymer Science
Composites in 25 kg batches were compounded of cellulose nanocrystals (CNC) and thermomechanical pulp (TMP) and shaped into caps at industrial facilities on a pilot‐plant scale. Some of the material was also injection molded into plaques to compare the effect of laboratory‐scale and pilot‐scale compounding of poly(ethylene‐co‐acrylic acid) (EAA7) and poly(caprolactone) composites reinforced with 10 wt% CNC and TMP. The materials compounded under laboratory‐scale conditions showed a different morphology, improved mechanical properties, and a higher viscosity, than the materials compounded on a pilot‐scale. In some cases, the rheological properties of the melts indicated the presence of a relatively strong percolating cellulosic network, and the interphase region between the cellulose and the matrix appears to be important for the mechanical performance of the composites. After the compounding on a pilot scale, both the length and width of the pulp fibers was reduced. The TMP provided better reinforcement than the CNC possibly due to the higher aspect ratio.
One-step reactive melt processing (REx) via radical reaction was evaluated with the aim of improving the rheological properties of poly(ε-caprolactone) (PCL). In particular, a water-assisted REx was designed under the hypothesis of increasing crosslinking efficiency with water as a low viscous medium in comparison with a slower PCL macroradicals diffusion in the melt state. To assess the effect of dry vs. water-assisted REx on PCL, its structural, thermo-mechanical and rheological properties were investigated. Water-assisted REx resulted in increased PCL gel fraction compared to dry REx (from 1 to 34 %), proving the rationale under the formulated hypothesis. From dynamic mechanical analysis and tensile tests, the crosslink did not significantly affect the PCL mechanical performance. Dynamic rheological measurements showed that higher PCL viscosity was reached with increasing branching/crosslinking and the typical PCL Newtonian behavior was shifting towards a progressively more pronounced shear thinning. A complete transition from viscous- to solid-like PCL melt behavior was recorded, demonstrating that higher melt elasticity can be obtained as a function of gel content by controlled REx. Improvement in rheological properties offers the possibility of broadening PCL melt processability without hindering its recycling by melt processing.
12 July 2024 in ACS Sustainable Chemistry & Engineering
Ethylene brassylate is a renewable macrolactone from castor oil that can be polymerized via ring-opening polymerization (ROP) to obtain a fully biosourced biodegradable polyester. ROP mediated by organometallic catalysts leads to high molar mass poly(ethylene brassylate) (PEB). However, the use of metal-free organocatalysis has several advantages, such as the reduction of toxic and expensive metals. In this work, a novel cellulose nanofibril (CNF)/PEB nanocomposite fabrication process by organocatalysis and reactive extrusion (REx) is disclosed. Here, ROP was carried out via solvent-free REx in the presence of CNFs using organic 1,5,7-triazabicyclo[4.4.0]dec-5-ene as a catalyst. Neat or lactate-esterified CNFs (LACNF) were used as initiators to investigate the effect of surface topochemistry on the in situ polymerization and the properties of the nanocomposites. A molar mass of 9 kDa was achieved in the presence of both unmodified and LACNFs with high monomer conversion (>98%) after 30 min reaction in a microcompounder at 130 °C. Tensile analysis showed that both nanofibril types reinforce the matrix and increase its elasticity due to the efficient dispersion obtained through the grafting from polymerization achieved during the REx. Mechanical recycling of the neat polymer and the nanocomposites was proven as a circular solution for the materials' end-of-life and showed that lactate moieties induced some degradation.